LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1025 (Engine Controls - 4.8L, 5.3L, & 6.0L (Troubleshooting & Diagnosis)) >> Troubleshooting >> Fuel Injector Balance Test with Tech 2 >> Test Description

Test Description

WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 5:  If the pressure drop value for each fuel injector is within 10 kPa (1.5 psi) of the average pressure drop value, the fuel injectors are flowing properly. Calculate the pressure drop value for each fuel injector by subtracting the second pressure reading from the first pressure reading.
Fuel Injector Balance Test with Tech 2

Step Action Values Yes No
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module (PCM) Connector End Views
1 Did you perform the Diagnostic System Check - Engine Controls? - Go to Step 2  Go to Diagnostic System Check - Engine Controls
2 Did you perform the Fuel Injector Coil Test? - Go to Step 3  Go to Fuel Injector Coil Test 
3
IMPORTANT: Do not perform this test if the engine coolant temperature (ECT) is above 94° C (201° F).
IMPORTANT: Verify there is adequate fuel in the fuel tank before proceeding with this diagnostic.
  1. Turn OFF the ignition.
  2. Turn OFF all accessories.
  3. Install the fuel pressure gage. Refer to Fuel Pressure Gage Installation and Removal .
  4. Turn ON the ignition, with the engine OFF.
  5. Command the fuel pump ON with a scan tool.
    6. IMPORTANT:
    • You may need to command the fuel pump ON a few times in order to obtain the highest possible fuel pressure.
    • Do not start the engine.
  6. Observe the fuel pressure gage, with the fuel pump commanded ON.
Is the fuel pressure within the specified value?		 385-425 kPa (55-62 psi) VIN: (V, T, U) Gasoline
335-375 kPa (48-54 psi) VIN: Z Ethanol		 Go to Step 4  Go to Fuel System Diagnosis 
4
IMPORTANT: The fuel pressure may vary slightly when the fuel pump stops operating. After the fuel pump stops operating, the fuel pressure should stabilize and remain constant.
Observe the fuel pressure gage for 1 minute.Does the fuel pressure drop more than the specified value?		 34 kPa (5 psi) Go to Fuel System Diagnosis  Go to Step 5 
5 
NOTE: Refer to Fuel Injector Balance Test Notice in Cautions and Notices.
  1. Select the Fuel Injector Balance Test function with a scan tool.
  2. Select an injector to be tested.
  3. Press Enter. This will prime the fuel system.
    4. IMPORTANT: Record the fuel pressure value immediately after the fuel injector stops pulsing. The fuel pressure may rise after the fuel injector stops pulsing. Do not record the higher fuel pressure value.
  4. Record the fuel pressure indicated by the fuel pressure gage after the fuel pressure stabilizes. This is the 1st pressure reading.
  5. Energize the fuel injector by depressing the Pulse Injector button on the scan tool. This will energize the injector and decrease the fuel pressure.
  6. Record the fuel pressure indicated by the fuel pressure gage after the fuel injector has stopped pulsing. This is the 2nd pressure reading.
  7. Press Enter again to bring you back to the Select Injector screen.
  8. Repeat for each fuel injector.
  9. Subtract the 2nd pressure reading from the 1st pressure reading for one fuel injector. The result is the pressure drop value.
  10. Obtain a pressure drop value for each fuel injector.
  11. Add all of the individual pressure drop values. This is the total pressure drop.
  12. Divide the total pressure drop by the number of fuel injectors. This is the average pressure drop.
Does any fuel injector have a pressure drop value that is either higher than the average pressure drop or lower than the average pressure drop by the specified value?		 10 kPa (1.5 psi) Go to Step 6  Go to Symptoms - Engine Controls 
6 Perform the Fuel Injector Cleaning Procedure .
Did you complete the procedure?		 - Go to Step 7  -
7 Operate the vehicle in order to verify the repair.
Does a driveability condition still exist?		 - Go to Symptoms - Engine Controls  System OK
scientia non olet · About LEMON Manuals