LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1022 (Engine Controls Diagnosis - 6.6L (Lb7) (DTCS P0612 To P2141)) >> Diagnosis >> DTC P2139 >> Conditions for Clearing the DTC

Conditions for Clearing the DTC

WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
DTC P2139

Step Action Values Yes No
Schematic Reference:  Engine Controls Schematics 
Connector End View Reference:  Engine Control Module (ECM) Connector End Views  or  Engine Controls Connector End Views 
1 Did you perform the Diagnostic System Check-Engine Controls? - Go to Step 2  Go to Diagnostic System Check - Engine Controls
2
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Does the DTC fail this ignition?		 - Go to Step 4  Go to Step 3 
3
  1. Select the diagnostic trouble code (DTC) option using the scan tool.
  2. Lightly touch and move the related accelerator pedal position (APP) wiring harnesses and connectors while monitoring the DTC information.
Did this DTC fail this ignition during the above test?		 - Go to Step 4  Go to Intermittent Conditions
4 Is DTC P2138 also set? - Go to DTC P2138  Go to Step 5 
5
  1. Turn OFF the ignition.
  2. Disconnect the APP sensor harness connector.
  3. Turn ON the ignition.
  4. Test for voltage at the APP sensor 3, 5-volt reference circuit with a test lamp connected to ground.
Does the test lamp illuminate?		 - Go to Step 6  Go to Step 10 
6 Connect a test lamp between the APP sensor 3, 5-volt reference circuit and the APP sensor 3 low reference circuit
Does the test lamp illuminate?		 - Go to Step 7  Go to Step 12 
7
  1. Disconnect the test lamp.
  2. With the APP sensor harness connector still disconnected, observe the APP sensor 2 and the APP sensor 3 voltage parameters with a scan tool.
Are both APP sensor 2 and 3 voltages above the specified value?		 4 V Go to Step 8  Go to Step 15 
8
  1. Probe the APP sensor 2 signal circuit with a test lamp connected to ground.
  2. Observe the APP sensor 2 and the APP sensor 3 voltage parameters with a scan tool.
Are both APP sensor 2 and 3 voltages below the specified value?		 1 V Go to Step 9  Go to Step 11 
9 Test the APP sensor 2 signal circuit for a short to the APP sensor 3 signal circuit with a DMM. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 17  Go to Step 15 
10
  1. Turn OFF the ignition.
  2. Disconnect the engine control module (ECM) harness connector that contains the APP sensor 3, 5-volt reference circuit.
  3. Test the APP sensor 3, 5-volt reference circuit for high resistance with a DMM. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 17  Go to Step 15 
11
  1. Turn OFF the ignition.
  2. Disconnect the engine control module (ECM) harness connector that contains the APP sensor 3 signal circuit.
  3. Turn ON the ignition.
  4. Test the APP sensor 3 signal circuit for high resistance with a DMM. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 17  Go to Step 13 
12
  1. Turn OFF the ignition.
  2. Disconnect the ECM harness connector that contains the APP sensor 3 low reference circuit.
  3. Test the APP sensor 3 low reference circuit for high resistance with a DMM. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 17  Go to Step 15 
13 Inspect for poor connections at the harness connector of the APP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Repairing Connector Terminals in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 17  Go to Step 14 
14 Replace the APP sensor assembly. Refer to Accelerator Pedal Position (APP) Sensor Replacement .
Did you complete the replacement?		 - Go to Step 17  -
15 Inspect for poor connections at the harness connector of the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Repairing Connector Terminals in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 17  Go to Step 16 
16 Replace the ECM. Refer to Engine Control Module (ECM) Replacement .
Did you complete the replacement?		 - Go to Step 17  -
17
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 18 
18 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List System OK
scientia non olet · About LEMON Manuals