LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2001 >> Venture Base, Van Passenger >> Repair and Diagnosis >> External Pages >> Different car >> Section 982 (Automatic Transaxle - AF33-5 (DTC P0562 - P0762)) >> Diagnostic Information & Procedures >> DTC P0736 >> Test Description

Test Description

WARNING: This page is about a different car, the 2003 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 5:  This step determines that shift solenoid 4 or the U1 shift valve is stuck if the TCC applies in 2nd gear and stalls the engine.
  2. 6:  This step determines if the output shaft speed sensor signal is skewed by a large factor.
  3. 7:  This step determines if the input shaft speed sensor signal is skewed by a large factor.
DTC P0736

Step Action Values Yes No
1 Did you perform the Diagnostic System Check - Engine Controls? - Go to Step 2  Go to DIAGNOSTIC SYSTEM CHECK -- ENGINE CONTROLS
2 Inspect for correct transmission fluid level. Refer to Transmission Fluid Checking Procedure .
Is the transmission fluid level correct?		 - Go to Step 4  Go to Step 3 
3
  1. Visually inspect the transmission cooling system for fluid leaks. Refer to Fluid Leak Diagnosis .
  2. Repair leaks as necessary.
  3. Fill the transmission to the proper fluid level.
Did you find and correct the condition?		 - Go to Step 19  Go to Step 4 
4
  1. Install a scan tool.
  2. Turn the ignition ON, with the engine OFF.
    3. IMPORTANT:
    • Before clearing the DTC, use the scan tool in order to record the ECM and the TCM Failure Records. Using the Clear Eng./Trans. DTC Info function erases the Failure Records from the ECM and TCM.
    • Using the Clear Eng./Trans. DTC Info function erases stored DTCs in both the ECM and TCM.
  3. Record the DTC Failure Records.
  4. Clear the DTC.
  5. Use the scan tool snapshot mode in order to record commanded gear and gear ratio.
  6. Drive the vehicle in REVERSE (R) and record the gear ratio while accelerating.
Is the reverse gear ratio within the specified range?		 3.68:1-5.52:1 Go to INTERMITTENTS Go to Step 5 
5  Drive the vehicle in 2nd gear.
Does the engine stall when the transmission shifts into 2nd gear?		 - Go to Step 10  Go to Step 6 
6 
  1. Drive the vehicle.
  2. Observe Transmission OSS with a scan tool.
  3. Compare with a known good vehicle.
Is Transmission OSS reading correctly?		 - Go to Step 7  Go to Step 15 
7 
  1. Stop the vehicle and apply the parking brake.
  2. Place the gear selector in PARK (P).
  3. Allow the engine to idle.
  4. Observe Transmission ISS with a scan tool.
Is Transmission ISS within the specified range?		 400-800 RPM Go to Step 8  Go to Step 14 
8 Perform a line pressure test. Refer to Line Pressure Check Procedure .
Is the action complete?		 - Go to Step 9  -
9
  1. Remove the control valve body cover (29). Refer to Control Valve Body Cover Removal .
  2. Inspect the inside of the control valve body cover (29) for excessive sediment.
Did you find excessive amounts of sediment?		 - Go to Step 13  Go to Step 11 
10 Inspect the control valve body assembly (39) for the following conditions:
  • Stuck 3-4, 4-5 shift solenoid valve assembly (S4) - blue (303)
  • Stuck U1 shift valve (386)

Refer to Control Valve Body Assembly Disassemble .
Did you find any of the above conditions?		 - Go to Step 16  Go to Step 12 
11 Inspect the control valve body assembly (39) for the following conditions:
  • Stuck M1 shift valve (389)
  • Stuck U1 shift valve (386)
  • Stuck U2 shift valve (392)
  • Stuck neutral relay valve (356)
  • Stuck line pressure control solenoid valve assembly (SLT) (316)

Refer to Rear Control Valve Body Disassemble and Middle Control Valve Body Disassemble .
Did you find any of the above conditions?		 - Go to Step 16  Go to Step 12 
12 Has the control valve body been serviced within the past 3 months or 4,828 km (3,000 mi)? - Go to Step 13  Go to Step 16 
13 Inspect the following items:
  • Direct clutch (C2) (556)
  • Low and reverse clutch (B3) (26)
  • 1-2, reverse clutch (B5) (620)

Refer to Forward and Direct Clutch Assembly Assemble , Front Internal Gear and Low and Reverse Clutch Installation , and 1-2 Reverse Clutch Assemble .
Is the action complete?		 - Go to Step 17  -
14 Replace the input shaft speed sensor (73). Refer to Input Shaft Speed Sensor Replacement .
Is the replacement complete?		 - Go to Step 19  -
15 Replace the output shaft speed sensor (62). Refer to Output Shaft Speed Sensor Replacement .
Is the replacement complete?		 - Go to Step 19  -
16 Repair or replace the control valve body assembly (39). Refer to Control Valve Body Replacement .
Is the action complete?		 - Go to Step 18  -
17 Repair or replace the transmission. Refer to Transmission Replacement .
Is the action complete?		 - Go to Step 18  -
18
  1. Replace the transmission fluid. Refer to Transmission Fluid Replacement .
  2. Inspect for the correct level of transmission fluid.
  3. Add new fluid as necessary.
    4. IMPORTANT: The Reset Trans Adapts function will clear all adapt cells. This may affect transmission performance. The TCM will update the adapt cell values as the vehicle is driven.
  4. Use the scan tool in order to perform the following:
    • Reset oil life monitor to 100 percent.
    • Reset Trans Adapts.
Did you complete the above procedures?		 - Go to Step 19  -
19 Perform the following procedure in order to verify the repair:
  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle.
  4. Select Specific DTC.
  5. Enter DTC P0736.

Does the DTC reset?		 - Go to Step 2  Go to Step 20 
20 With the scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to DIAGNOSTIC TROUBLE CODE DEFINITIONS System OK
scientia non olet · About LEMON Manuals