LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2001 >> Venture Base, Van Passenger >> Repair and Diagnosis >> External Pages >> Different car >> Section 974 (Wheel Drive Shafts) >> Repair Instructions >> Wheel Drive Shaft Replacement - Rear >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2003 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Rear Brake Drum & Wheel Drive Shaft Spindle Nut
    GM933721Courtesy of GENERAL MOTORS CORP.
  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Remove and discard the wheel drive shaft spindle nut.
    4. Fig 2: View Of Stabilizer Link At Lower Control Arm Nut
    GM928802Courtesy of GENERAL MOTORS CORP.
  4. While holding the stabilizer link with a wrench, remove the stabilizer link-to-lower control arm nut.
  5. Disconnect the link from the control arm.
    6. Fig 3: Jackstand Supporting Lower Control Arm
    GM928818Courtesy of GENERAL MOTORS CORP.
  6. Place a stand under the lower control arm and support the control arm.
    7. Fig 4: Lower Shock Bolt
    GM928822Courtesy of GENERAL MOTORS CORP.
  7. Remove the lower shock absorber mounting bolt and nut.
    8. Fig 5: Removing Washer, Bolt & Nut On Suspension Knuckle
    GM929839Courtesy of GENERAL MOTORS CORP.
  8. Remove the toe link nut, bolt, and washer.
    9. Fig 6: View Of Lower Suspension Jounce Bumper Nut
    GM930250Courtesy of GENERAL MOTORS CORP.
  9. Loosen, but do not remove, the lower suspension jounce bumper nut.
    10. Fig 7: Lower Control Arm, Knuckle Nut & Bolt
    GM928825Courtesy of GENERAL MOTORS CORP.
  10. Remove the lower control arm-to-suspension knuckle bolt and nut.
    11. Fig 8: Control Arm & Coil Spring
    GM929563Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Relieve spring tension slowly in order to avoid sudden release of the coil spring.
  11. Slowly lower support stand until coil spring tension is relieved and remove coil spring.
    12. Fig 9: ABS Brake Harness, Upper Control Arm, Knuckle Nut & Bolt
    GM929585Courtesy of GENERAL MOTORS CORP.
  12. Loosen, but do not remove, the upper control arm-to-suspension knuckle nut.
    13. IMPORTANT: Support the wheel drive shaft while it is disengaged from the wheel hub and bearing assembly in order to avoid damaging the wheel drive shaft seals.
    Fig 10: Placing Block Of Wood Against Wheel Drive Shaft Spindle & Tap With Hammer
    GM929594Courtesy of GENERAL MOTORS CORP.
  13. Place a block of wood against the wheel drive shaft spindle and tap with a hammer to release the spindle from the wheel hub and bearing assembly.
    14. Fig 11: Rotating Suspension Knuckle Upward & Secure With Heavy Mechanics Wire
    GM929646Courtesy of GENERAL MOTORS CORP.
  14. Rotate the suspension knuckle upward and secure with heavy mechanics wire, or equivalent.
    15. Fig 12: Removing Wheel Drive Shaft From Vehicle
    GM932795Courtesy of GENERAL MOTORS CORP.
  15. Assemble the J 45341  and the J-2619-A to the wheel drive shaft inner tripot joint. See Special Tools .
  16. Disengage the tripot joint from the rear drive module (RDM).
  17. Remove the wheel drive shaft from the vehicle.
    18. Fig 13: Wheel Drive Shaft Retaining Ring
    GM931469Courtesy of GENERAL MOTORS CORP.
  18. Remove and discard the wheel drive shaft retaining ring.
scientia non olet · About LEMON Manuals