Disc Brake Component Specifications

Application	Specification
Application	Metric	English
Front Brakes JC5/JH5
Rotor Discard Thickness *	27.50 mm	1.083 in
Rotor Minimum Allowable Thickness After Refinish	28.0 mm	1.102 in
Rotor Thickness (new)	29.0 mm	1.142 in
Rotor Maximum Allowable Lateral Runout	0.13 mm	0.005 in
Rotor Maximum Allowable Scoring	1.50 mm	0.059 in
Rotor Maximum Allowable Thickness Variation	0.025 mm	0.0001 in
Front Brakes JH6
Rotor Discard Thickness *	36.50 mm	1.437 in
Rotor Minimum Allowable Thickness After Refinish	37.0 mm	1.457 in
Rotor Thickness (new)	38.0 mm	1.496 in
Rotor Maximum Allowable Lateral Runout	0.13 mm	0.005 in
Rotor Maximum Allowable Scoring	1.50 mm	0.059 in
Rotor Maximum Allowable Thickness Variation	0.025 mm	0.001 in
Front Brakes JH7
Rotor Discard Thickness *	36.50 mm	1.437 in
Rotor Minimum Allowable Thickness After Refinish	37.0 mm	1.46 in
Rotor Thickness (new)	38.0 mm	1.50 in
Rotor Maximum Allowable Lateral Runout	0.13 mm	0.005 in
Rotor Maximum Allowable Scoring	1.50 mm	0.059 in
Rotor Maximum Allowable Thickness Variation	0.025 mm	0.001 in
Rear Brakes JC5/JH5 Pickup
Rotor Discard Thickness *	18.50 mm	0.728 in
Rotor Minimum Allowable Thickness After Refinish	19.0 mm	0.748 in
Rotor Thickness (new)	20.0 mm	0.787 in
Rotor Maximum Allowable Lateral Runout	0.13 mm	0.005 in
Rotor Maximum Allowable Scoring	1.50 mm	0.059 in
Rotor Maximum Allowable Thickness Variation	0.025 mm	0.001 in
Rear Brakes JC5/JH5 Utility
Rotor Discard Thickness *	28.50 mm	1.122 in
Rotor Minimum Allowable Thickness After Refinish	29.0 mm	1.142 in
Rotor Thickness (new)	30.0 mm	1.181 in
Rotor Maximum Allowable Lateral Runout	0.13 mm	0.005 in
Rotor Maximum Allowable Scoring	1.50 mm	0.059 in
Rotor Maximum Allowable Thickness Variation	0.025 mm	0.001 in
Rear Brakes JH6
Rotor Discard Thickness *	27.50 mm	1.083 in
Rotor Minimum Allowable Thickness After Refinish	28.0 mm	1.102 in
Rotor Thickness (new)	29.0 mm	1.142 in
Rotor Maximum Allowable Lateral Runout	0.13 mm	0.005 in
Rotor Maximum Allowable Scoring	1.50 mm	0.059 in
Rotor Maximum Allowable Thickness Variation	0.025 mm	0.001in
Rear Brakes JH7
Rotor Discard Thickness *	28.5 mm	1.122 in
Rotor Minimum Allowable Thickness After Refinish	29.0 mm	1.142 in
Rotor Thickness (new)	30.0 mm	1.181 in
Rotor Maximum Allowable Lateral Runout	0.13 mm	0.005 in
Rotor Maximum Allowable Scoring	1.50 mm	0.059 in
Rotor Maximum Allowable Thickness Variation	0.025 mm	0.001 in
* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this specification. After refinishing the rotor, replace any rotor that does not meet the minimum thickness specifications.