LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2000 >> Suburban C2500 >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Analog Instrument Panels - New Style >> Removal & Installation >> Instrument Panel (I/P) Carrier Replacement >> Installation

Instrument Panel (I/P) Carrier Replacement: Installation

  1. Position the instrument panel carrier (1) in the vehicle.
    Fig 1: Positioning I/P Carrier
    G01579464Courtesy of GENERAL MOTORS CORP.
  2. Install the instrument panel carrier top bolts (1).

    Tighten 

    Tighten the bolts to 50 N.m (37 lb ft).

    Fig 2: Installing I/P Carrier Top Bolts
    G01579465Courtesy of GENERAL MOTORS CORP.
  3. Install the instrument panel carrier retaining bolts.

    The left side is shown in illustration, the right is similar.

    Tighten 

    Tighten the bolt to 50 N.m (37 lb ft).

    Fig 3: Installing I/P Carrier Retaining Bolts
    G01579466Courtesy of GENERAL MOTORS CORP.
  4. Install the instrument panel center support bracket bolt.

    Tighten 

    Tighten the bolt to 25 N.m (18 lb ft).

    Fig 4: Installing I/P Center Support Bracket Bolt
    G01579467Courtesy of GENERAL MOTORS CORP.
  5. Install the instrument panel center support bracket bezel (1).
    Fig 5: Installing I/P Center Support Bracket Bezel
    G01579468Courtesy of GENERAL MOTORS CORP.
  6. Install the right side of the carrier to the vehicle, if the HVAC module was removed.
    7. Fig 6: Installing Right Side Of Carrier
    G01579469Courtesy of GENERAL MOTORS CORP.
  7. Install the retaining bolts.

    Tighten 

    Tighten the bolts to 50 N.m (37 lb ft).

  8. Attach the instrument panel harness to the carrier.
  9. Install the amplifier, if equipped.
  10. Install the cross car duct.
  11. Install the antenna cable to the cross car duct.
  12. Install the transfer case control module to the bracket, if equipped. Refer to REMOVAL & INSTALLATION .
  13. Connect all of the electrical connectors to the wiring harness junction block.
  14. Install the instrument panel upper brackets.

    Tighten 

    Tighten the retaining bolts to 2 N.m (18 lb in).

    Fig 7: Installing I/P Upper Brackets & Bolts
    G01579470Courtesy of GENERAL MOTORS CORP.
  15. Install the instrument panel assembly to the vehicle.
  16. Install the instrument panel assembly retaining bolts (3) and nuts (4).

    Ensure the wire harness is routed to all of the openings.

    Tighten 

    Tighten the retaining bolts and nuts to 9 N.m (80 lb in).

    Fig 8: Installing I/P Assembly Retaining Bolts & Nuts
    G01579471Courtesy of GENERAL MOTORS CORP.
  17. Install the harness hold down retainers to the instrument panel assembly.
  18. Install the harness to the instrument panel.
  19. Install both front window air duct to the instrument panel assembly.
  20. Install the instrument panel cluster assembly. Refer to INSTRUMENT PANEL CLUSTER (IPC) .
  21. Install the park brake release lever to the instrument panel. Refer to DISC BRAKES & DRUM BRAKES .
  22. Install the data link connector to the instrument panel.
  23. Install the remote control door lock receiver module, if equipped.
  24. Install the VCU, if equipped.
  25. Install the VIU, if equipped.
  26. Install the steering column. Refer to STEERING COLUMN REPLACEMENT .
  27. Install the left air louver housing.
  28. Install the accessory switch housing.
  29. Install the HVAC control. Refer to appropriate HVAC SYSTEMS article.
  30. Install the radio.
  31. Install the passenger side airbag module. Refer to AIR BAG MODULES .
  32. Install the lower trim panel.
  33. Install the driver side knee bolster.
  34. Install the center console, if equipped.
  35. Install the instrument panel trim panel.
  36. Connect the negative battery cable.
scientia non olet · About LEMON Manuals