LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 1990 >> Step Van 7.4 N, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 16 (Suspension - Front (AWD & 4WD)) >> Torque Specifications

Torque Specifications

WARNING: This page does not describe the selected car, but rather 15 other vehicles, including the 1992 Oldsmobile Bravada, 1992 GMC Yukon, 1992 GMC Suburban, 1992 GMC Sonoma, and 1992 GMC Safari. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Astro & Safari
Ball Joint-To-Control Arm Nuts (5) 22 (30)
Ball Joint-To-Steering Knuckle Nut (1)(5)
Lower 92 (125)
Upper 94 (128)
Drive Axle Shaft Nut 173 (234)
Drive Axle Shaft-To-Differential Drive Flange Bolts 60 (80)
Hub & Bearing-To-Steering Knuckle Bolts 66 (90)
Lower Control Arm-To-Frame Pivot Bolt Nuts (2)(3)(5) 135 (185)
Shock Absorber Nuts (4) 66 (89)
Splash Shield Bolts 12 (16)
Stabilizer Bar Clamp-To-Frame Bolts 12 (16)
Stabilizer Bar Spacer Bolt 22 (33)
Tie Rod End-To-Steering Knuckle Nut 35 (47)
Torsion Bar Retainer-To-Support Nuts
Center Nut 18 (24)
Edge Nuts 46 (62)
Upper Control Arm-To-Frame Pivot Bolt Nuts (2)(5) 88 (120)
"K" Series Blazer & Pickup, Sierra, Suburban & Yukon
Ball Joint-To-Control Arm Nuts (5)
Lower 45 (60)
Upper
K15 & K25 Series Pickup and Sierra, Suburban & Yukon 17 (23)
K35 Series Pickup & Sierra K35 52 (70)
Ball Joint-To-Steering Knuckle Nut (1)(5)
Lower 94 (128)
Upper 84 (115)
Drive Axle Shaft Nut 173 (234)
Drive Axle Shaft-To-Differential Drive Flange Bolts 60 (80)
Hub & Bearing-To-Steering Knuckle Bolts 133 (180)
Lower Control Arm-To-Frame Pivot Bolt Nuts (2)(3)(5) 135 (185)
Shock Absorber Nuts (4) 66 (89)
Splash Shield Bolts 19 (26)
Stabilizer Bar Clamp-To-Frame Bolts 13 (18)
Stabilizer Bar Spacer Nut 12 (16)
Tie Rod End-To-Steering Knuckle Nut 35 (47)
Torsion Bar Retainer-To-Support Nuts
Center Nut 18 (24)
Edge Nuts 46 (62)
Upper Control Arm-To-Frame Pivot Bolt Nuts (2)(5) 139 (188)
Bravada, Jimmy, Sonoma, Syclone, Typhoon & "T" Series Blazer & Pickup
Ball Joint-To-Control Arm Nuts (5) 17 (23)
Ball Joint-To-Steering Knuckle Nut (1)(5)
Lower 83 (112)
Upper 61 (83)
Drive Axle Shaft Nut 181 (245)
Hub & Bearing/Shield-To-Steering Knuckle Bolts 86 (117)
Lower Control Arm-To-Frame Pivot Bolts (4)(5) 148 (201)
Lower Control Arm-To-Frame Pivot Bolt Nuts (2)(4)(5) 92 (125)
Shock Absorber Nuts (3) 54 (73)
Stabilizer Bar Clamp-To-Frame Bolts 35 (47)
Stabilizer Bar-To-Lower Control Arm Bolts 24 (33)
Tie Rod End-To-Steering Knuckle Nut 35 (47)
Torsion Bar Retainer-To-Support Bolts 26 (35)
Torsion Bar Retainer-To-Support Nut 25 (34)
Upper Control Arm-To-Frame Pivot Bolt Nuts (5) 70 (95)
(1) Tighten nut to align cotter pin hole. DO NOT tighten nut more than an additional 1/6 turn to align cotter pin hole.
(2) Use NEW nuts during reassembly.
(3) Install both bolts with nuts facing rear of vehicle.
(4) Install upper/rear bolt with nut facing rear of vehicle. Install lower/front bolt with nut facing front of vehicle.
(5) Complete tightening of bolts and/or nuts with vehicle at proper riding height specification.
scientia non olet · About LEMON Manuals