Removal Procedure

Courtesy of GENERAL MOTORS COMPANY

Hood Rear Outer Air Inlet Seal Retainer (1) - Remove [2x]
Hood Rear Outer Air Inlet Seal (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

Front Compartment Side Sight Shield Retainer (1) - Remove [2x]
Front Compartment Side Sight Shield (2) - Remove
Place a clean suitable drain pan under the windshield washer solvent container to recover the windshield washer solvent.
Courtesy of GENERAL MOTORS COMPANY

Windshield Washer Solvent Container Filler Tube Bracket Bolt (1) - Remove
While twisting, pull inboard on the windshield washer solvent container filler tube (2) to remove it from the windshield washer solvent container grommet.
Remove the tire and wheel assembly. Tire and Wheel Removal and Installation
Courtesy of GENERAL MOTORS COMPANY
NOTE:
- Quantity of fasteners may vary based on option content.
- Components removed for graphic clarity.
Engine Front Splash Shield Retainer (1) - Remove [2x]
Engine Front Splash Shield Bolt (2) - Remove [5x]
Engine Front Splash Shield (3) - Remove
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Remove only the outer front tire front air deflector bolt. The front tire front air deflector will be removed with the front wheelhouse liner.

Front Tire Front Air Deflector Bolt (1) - Remove
Front Bumper Fascia Air Deflector Bolt (2) - Remove [2x]
Front Bumper Fascia Center Support Bolt (3) - Remove [3x]
Courtesy of GENERAL MOTORS COMPANY

Front Wheelhouse Liner Retainer (1) - Remove [4x]
Front Wheelhouse Liner Bolt (2) - Remove [7x]
Front Wheelhouse Liner (3) - Remove
Courtesy of GENERAL MOTORS COMPANY

Disconnect the electrical connectors.
Release the windshield washer solvent container wiring harness retainers (1) and reposition the windshield washer solvent container wiring harness as necessary.
Windshield Washer Pump Hose (2) - Disconnect and reposition
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Support the windshield washer solvent container while removing the windshield washer solvent container bolts.

Windshield Washer Solvent Container Bolt (1) - Remove [2x]
Windshield Washer Solvent Container (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

Front Fender Insulator Retainer (1) - Remove
Pull the front fender insulator (2) down and out from the front fender.
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia (1) - Remove - Front Bumper Fascia Removal and Installation
Courtesy of GENERAL MOTORS COMPANY

Headlamp Bolt (1) - Remove
Front Bumper Fascia Guide Bolt (2) - Remove [2x]
Front Bumper Fascia Guide (3) - Remove
Courtesy of GENERAL MOTORS COMPANY

Front Fender Bolt (1) - Remove [2x]
Headlamp Bolt (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Remove only the outer rear tire front air deflector bolt. The rear tire front air deflector will be repositioned with the rear wheelhouse liner.

Rear Tire Front Air Deflector Bolt (1) - Remove [3x]
Rear Tire Front Air Deflector (2) - Remove
Rear Wheelhouse Liner Retainer (3) - Remove
Rear Wheelhouse Liner (4) - Reposition
Courtesy of GENERAL MOTORS COMPANY

Using an appropriate trim tool, release the lower rocker panel molding retainers (1) and pull the rocker panel molding (2) away from the body side outer panel.
Using an appropriate trim tool, release the upper rocker panel molding retainers (1) and pull the rocker panel molding (2) away from the body side outer panel.
Rocker Panel Molding (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

Front Fender Bolt (1) - Remove [4x]

NOTE:

Apply a double layer of masking tape to the windshield to prevent damaging the windshield.

Front Fender Screw (2) - Remove [2x]
Front Fender Nut (3) - Remove
Courtesy of GENERAL MOTORS COMPANY

Front Fender - Right Side - Remove