Installation Procedure

Courtesy of GENERAL MOTORS COMPANY

Front Fender - Right Side - Install
Courtesy of GENERAL MOTORS COMPANY

CAUTION:
Refer to Fastener Caution .

Front Fender Bolt (1) - Install and tighten [4x] - Fastener Specifications
Front Fender Screw (2) - Install and tighten - Fastener Specifications
Front Fender Nut (3) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Headlamp Bolt (1) - Install and tighten [2x] - Fastener Specifications
Front Fender Bolt (2) - Install and tighten - Fastener Specifications [2x]
Courtesy of GENERAL MOTORS COMPANY

Front Fender Insulator (2) - Install
Front Fender Insulator Retainer (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Windshield Washer Solvent Container (2) - Install
Windshield Washer Solvent Container Bolt (1) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Windshield Washer Pump Hose (2) - Connect
Install the windshield washer solvent container wiring harness retainers (1).
Connect the electrical connectors.
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Guide (3) - Install
Front Bumper Fascia Guide Bolt (2) - Install and tighten [2x] - Fastener Specifications
Headlamp Bolt (1) - Install - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia (1) - Install - Front Bumper Fascia Removal and Installation
Courtesy of GENERAL MOTORS COMPANY

Position the rocker panel molding (2) to the vehicle and seat the upper rocker panel molding retainers (1) into the body side outer panel.
Seat the lower rocker panel molding retainers (1) into the body side outer panel.
Courtesy of GENERAL MOTORS COMPANY

Position the rear wheelhouse liner (4) to its original location.
Rear Wheelhouse Liner Retainer (3) - Install
Rear Tire Front Air Deflector (2) - Install
Rear Tire Front Air Deflector Bolt (1) - Install and tighten [3x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Wheelhouse Liner (3) - Install
Front Wheelhouse Liner Bolt (2) - Install and tighten [7x] - Fastener Specifications
Front Wheelhouse Liner Retainer (1) - Install [4x]
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Center Support Bolt (3) - Install and tighten [3x] - Fastener Specifications
Front Bumper Fascia Air Deflector Bolt (2) - Install and tighten [2x] - Fastener Specifications
Front Tire Front Air Deflector Bolt (1) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY
NOTE:
- Quantity of fasteners may vary based on option content.
- Components removed for graphic clarity.
Engine Front Splash Shield (3) - Install
Engine Front Splash Shield Bolt (2) - Install and tighten [5x] - Fastener Specifications
Engine Front Splash Shield Retainer (1) - Install [2x]
Install the right front tire and wheel assembly. Tire and Wheel Removal and Installation
Courtesy of GENERAL MOTORS COMPANY

Lubricate the end of the windshield washer solvent container filler tube (2) with full strength windshield washer fluid.
While twisting, push the windshield washer solvent container filler tube (2) into the windshield washer solvent container grommet until fully seated.
Windshield Washer Solvent Container Filler Tube Bracket Bolt (1) - Install and tighten - Fastener Specifications
Install the tire and wheel assembly. Tire and Wheel Removal and Installation
Courtesy of GENERAL MOTORS COMPANY

Front Compartment Side Sight Shield (2) - Install
Front Compartment Side Sight Shield Retainer (1) - Install [2x]
Courtesy of GENERAL MOTORS COMPANY

Hood Rear Outer Air Inlet Seal (2) - Install
Hood Rear Outer Air Inlet Seal Retainer (1) - Install [2x]
Courtesy of GENERAL MOTORS COMPANY

Install the air inlet grille panel extension (1).
Remove the masking tape.
Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.