Installation Procedure
Front Compartment Front Panel (1) - Install
- CAUTION:
Refer to Fastener Caution .
Front Compartment Front Panel Bolt - Left Side (1) - Install and tighten [3x] - Fastener Specifications
Front Fender Bolt - Left Side (1) - Install and tighten [2x] - Fastener Specifications
- Front Compartment Front Panel Bolt - Left Side (2) - Install and tighten [3x] - Fastener Specifications
- Reposition the wiring harness.
Front Compartment Front Panel Bolt - Left Side (1) - Install and tighten [2x] - Fastener Specifications
Front Compartment Front Panel Bolt - Right Side - Install and tighten [3x] - Fastener Specifications
Front Fender Bolt (1) - Right Side - Install and tighten [2x] - Fastener Specifications
- Front Compartment Front Panel Bolt - Right Side (2) - Install and tighten [3x] - Fastener Specifications
Front Compartment Front Panel Bolt - Right Side (1) - Install and tighten [2x] - Fastener Specifications
- Position the wiring harness.
Hood Hold Open Rod (2) - Install
- Hood Hold Open Rod Bolt (1) - Install and tighten [2x] - Fastener Specifications
Forward Lamp Wire Harness Ground Terminal (2) - Install [2x]
- Forward Lamp Wire Harness Ground Bolt (1) - Install and tighten [2x] - Ground Repair
Engine Wire Harness Ground Terminal (2) - Install
- Engine Wire Harness Ground Bolt (1) - Install and tighten - Ground Repair
Connect the transmission control module electrical connector (3)
- Battery Negative Cable Ground (2) - Install
- Battery Negative Cable Ground Bolt (1) - Install and tighten - Fastener Specifications
Engine Control Module Bracket (2) - Install
- Engine Control Module Bracket Nut (1) - Install and tighten - Fastener Specifications
Body Wiring Harness Fuse Block Bracket (2) - Install
- Body Wiring Harness Fuse Block Bracket Bolt (1) - Install and tighten [2x] - Fastener Specifications
Air Cleaner Assembly - (3) Install
- Air Cleaner Bolt (1) - Install and tighten - Fastener Specifications
- Air Cleaner Clamp (1) - Tighten
Intake Air Duct (1) - Install
Radiator Air Front Upper Baffle (2) - Install
- Install the 3 radiator air front upper baffle retainers (1).
Radiator Air Front Upper Baffle (1) - Install
Radiator Air Upper Baffle Retainer (2) - Install [4x]
Connect the electrical connector.
- Slide the sensor into the keyhole slot.
- Airbag Front End Discriminating Sensor (1) - Install and tighten - Fastener Specifications
Airbag Front End Discriminating Sensor Protector (2) - Install [2x]
- Airbag Front End Discriminating Sensor Bolt (1) - Install and tighten [2x] - Fastener Specifications
Radiator Air Upper Baffle (2) - Install
- Radiator Air Upper Baffle Retainer (1) - Install [7x]
Hood Primary and Secondary Latch (1) - Install
- Install the hood cable retainer.
Align the hood primary and secondary latch (1) with the marks made during removal.
- Hood Primary and Secondary Latch Bolt (2) - Install and tighten [2x] - Fastener Specifications
Radiator Upper Bracket - Right Side (3) - Install
- Radiator Upper Bracket Bolt (2) - Install and tighten [2x] - Fastener Specifications
- Wiring Harness Retainer (1) - Install
Radiator Upper Bracket - Left Side (2) - Install
- Radiator Upper Bracket Bolt (1) - Install and tighten [2x] - Fastener Specifications
Front Bumper Impact Bar (2) - Install
- Front Bumper Impact Bar Bolt (1) - Install and tighten [8x] - Fastener Specifications
- Install the wiring harness retainers.
Horn (2) - Install [2x]
- Horn Bolt (1) - Install and tighten [2x] - Fastener Specifications
- Connect the electrical connectors.
Front Bumper Fascia Center Support (2) - Install
- Front Bumper Fascia Center Support Bolt (1) - Install and tighten [2x] - Fastener Specifications
Headlamp Bolt (1) - Install and tighten [2x] - Fastener Specifications
- Radiator Air Upper Baffle Retainer (2) - Install [2x]
Front End Sheet Metal Cross Brace (2) - Install [2x]
- Front End Sheet Metal Cross Brace Bolt (1) - Install and tighten [4x] - Fastener Specifications
Front End Sheet Metal Cross Brace - Right Side (2) - Install
- Front End Sheet Metal Cross Brace Bolt (1) - Install and tighten [2x] - Fastener Specifications
- NOTE:
Forward range radar sensor will be with the bracket.
Forward Range Radar Bracket (2) - Install
- Front Bumper Fascia Support Brace Bolt (1) - Install and tighten [3x] - Front Bumper Shutter Replacement
Position the engine auxiliary radiator assembly (1) to the vehicle.
Charge Air Cooler Bracket Bolt (1) - Install and tighten [3x] - Fastener Specifications
- Charge Air Cooler Upper Bracket Nut (2) - Tighten - Fastener Specifications
Auxiliary Radiator Front Duct (1) - Install
Auxiliary Radiator Duct Retainer (1) - Install [2x]
Auxiliary Radiator Duct Retainer (1) - Install [3x]
- Install the front bumper fascia. Front Bumper Fascia Removal and Installation
Auxiliary Radiator Rear Duct (1) - Install
Auxiliary Radiator Duct Retainer (1) - Install [3x]
Position the engine auxiliary radiator assembly - left side (1).
Charge Air Cooler Bracket Bolt (2) - Install and tighten [3x] - Fastener Specifications
- Charge Air Cooler Upper Bracket Nut (1) - Tighten - Fastener Specifications
Auxiliary Radiator Front Duct (1) - Install
Auxiliary Radiator Duct Retainer (1) - Install [2x]
Auxiliary Radiator Duct Retainer (1) - Install [3x]
- Install the front bumper fascia. Front Bumper Fascia Removal and Installation
Auxiliary Radiator Rear Duct (1) - Install
Auxiliary Radiator Duct Retainer (1) - Install [3x]
Install the left and right side front bumper fascia support outer brace (2).
- Install the 2 left and right side front bumper fascia support outer brace bolt (1). Fastener Specifications
- NOTE:
Left side shown, right side similar.
Connect all electrical connectors.
- Install the left and right side headlamps (2)
- Secure the front headlamp guide pin to the front bumper fascia guide (1).
Secure the wiring harness retaining tab.
- Headlamp Bolt (1) - Install and tighten - Fastener Specifications
Headlamp Bolt (1) - Install and tighten [3x] - Fastener Specifications
- NOTE:
The front bumper fascia will rest in place by guides on the center support upper structure.
With the aid of an assistant, install the fascia (1)
Front Bumper Fascia Center Air Deflector Screw (1) - Install and tighten [6x] - Fastener Specifications
- Front Bumper Fascia Center Air Deflector Bolt (2) - Install and tighten [5x] - Fastener Specifications
- Front Bumper Fascia Center Air Deflector Retainer (3) - Install and tighten [2x] - Fastener Specifications
Front Bumper Fascia Center Air Deflector Screw (1) - Install and tighten [3x] - Fastener Specifications
Install the left side of the front bumper fascia (1) to the front bumper fascia guide (2) and the front headlamp (3).
Connect the electrical connector (1)
Install the right side of the front bumper fascia (1) to the front bumper fascia guide (2) and the front headlamp (3).
Front Bumper Fascia Bolt (1) - Install and tighten [6x] - Fastener Specifications
- Raise and support the vehicle. Lifting and Jacking the Vehicle
Install and tighten the left side upper front bumper fascia bolt (2). Fastener Specifications
Install and tighten the right side upper front bumper fascia bolt (2). Fastener Specifications
Front Bumper Fascia Bolt - Right Side (3) - Install and tighten [2x] - Fastener Specifications
- NOTE:
Left side shown, right side similar.
Install the left and right front wheelhouse liners (3).
- Front Wheelhouse Liner Retainer (2) - Install [8x]
- Front Wheelhouse Liner Bolt (1) - Install and tighten [14x] - Fastener Specifications
- NOTE:
Left side shown, right side similar.
Front Bumper Fascia Air Deflector Bolt (1) - Install and tighten [6x] - Fastener Specifications
- Front Bumper Fascia Bolt (2) - Install and tighten [4x] - Fastener Specifications
- NOTE:
- Left side shown, right side similar.
- Quantity of fasteners may vary based on option content.
- Components removed for graphic clarity.
Engine Front Splash Shield (3) - Install [2x]
- Engine Front Splash Shield Retainer (2) - Install [4x]
- Engine Front Splash Shield Bolt (1) - Install and tighten [10x] - Fastener Specifications
- NOTE:
- Left side shown, right side similar.
- Quantity of fasteners may vary based on option content.
Front Tire Front Air Deflector (2) - Install [2x]
- Front Tire Front Air Deflector Bolt (1) - Install and tighten [8x] - Fastener Specifications
- Install the tire and wheel assembly. Tire and Wheel Removal and Installation
- Lower the vehicle.
- Connect the negative battery cable. Battery Negative Cable Disconnection and Connection
- Enable the SIR System. SIR Disabling and Enabling