Installation Procedure
Connect the electrical connector.
- Instrument Panel Lower Center Trim Panel (2) - Install
- Instrument Panel Center Trim Panel Bolt (1) - Install and tighten [6x] - Fastener Specifications
Slide the front floor console (1) back into the instrument panel.
Engage the tabs (3) on both sides of the front floor console.
- Connect the front floor console harness connector on both sides of the front floor console.
- Front Floor Console Bolt (1) - Install and tighten [6x] - Fastener Specifications
- Front Floor Console Bracket Bolt (2) - Install and tighten [2x] - Fastener Specifications
Front Floor Console Extension Panel - Right Side (1) - Install
- Return the seat to its original position.
Front Floor Console Extension Panel - Left Side (1) - Install
- Return the seat to its original position.
Instrument Panel Trim Pad (1) - Install
Connect the electrical connectors.
- Instrument Panel Compartment (1) - Install
Instrument Panel Compartment Bolt (1) - Install and tighten [5x] - Fastener Specifications
Connect the electrical connector.
- Instrument Panel Lower Airbag - Passenger Side (2) - Install
- Instrument Panel Lower Airbag Nut (1) - Install and tighten [2x] - Fastener Specifications
Connect the electrical connectors.
- Instrument Panel Lower Trim Panel Insulator (1) - Install
- Install the front edge of the front floor console extension panel into the instrument panel lower trim panel insulator (1).
Instrument Panel Insulator Bolt (1) - Install and tighten [4x] - Fastener Specifications
- Connect and position the wiring harness.
Unlock and lower the body control module bracket (2).
- Connect the electrical connectors.
- Close and lock the body control module bracket (2) into the instrument panel lower trim panel insulator.
- Body Control Module Bracket Bolt (1) - Install and tighten - Fastener Specifications
{If equipped} Connect the electrical connector.
- Instrument Panel Outer Trim Cover - Right Side (1) - Install
Connect and position the wiring harness.
- Instrument Panel Knee Bolster (1) - Install
Data Link Connector Bolt (1) - Install and tighten [2x] - Fastener Specifications
- Instrument Panel Knee Bolster Bolt (2) - Install and tighten [3x] - Fastener Specifications
Instrument Panel Center Trim Pad (1) - Install
- Return the steering column to its original position.
Connect the electrical connector.
- Instrument Panel Lower Trim Panel Insulator (1) - Install
Install the tabs into the instrument panel lower trim panel insulator (1).
Instrument Panel Lower Trim Panel Insulator Retainer (1) - Install
- Instrument Panel Insulator Bolt (2) - Install and tighten [2x] - Fastener Specifications
- Instrument Panel Insulator Nut (3) - Install and tighten [2x] - Fastener Specifications
Attach the hood primary latch release cable end retainer to the hood primary latch release cable handle (1).
Instrument Panel Outer Trim Cover - Left Side (1) - Install
Connect the electrical connector.
- Instrument Panel Lower Airbag - Driver Side (2) - Install
- Instrument Panel Lower Airbag Nut (1) - Install and tighten [2x] - Fastener Specifications
Connect the electrical connector.
- Hazard Warning Switch (2) - Install
- Firmly secure the hazard warning switch (2) straight forward and ensure it is fully seated.
- Hazard Warning Switch Bolt (1) - Install and tighten [2x] - Fastener Specifications
Connect the electrical connector.
- Heater and Air Conditioning User Interface Control (2) - Install
- Heater and Air Conditioning Control Bolt (1) - Install and tighten [2x] - Fastener Specifications
Instrument Panel Trim Plate (2) - Install
- Instrument Panel Center Air Outlet Bolt (1) - Install and tighten [3x] - Fastener Specifications
- Connect the electrical connectors.
Radio Control (2) - Install
- Radio Control Bolt (1) - Install and tighten [2x] - Fastener Specifications
Instrument Panel Radio Front Trim Plate (1) - Install
Instrument Panel Radio Front Trim Plate (1) - Install
- Enable the SIR System. SIR Disabling and Enabling
- Clear DTCs
Refer to Fastener Caution .