LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 57 (Engine Heating And Cooling - Repair Instructions (1 Of 2)) >> Repair Instructions >> Engine Oil Cooler Adapter Replacement (LF4) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5876043

    Engine Oil Cooler Adapter (1) - Install

  2. GM5876038
    CAUTION:

    Refer to Fastener Caution .

    Engine Oil Cooler Adapter Bolt (1) - Install and tighten [3x] - Fastener Specifications

  3. GM5876024

    Engine Oil Cooler Pipe (2) @ Oil Filter Adapter - Install

  4. Retaining Clip (1) - Install
  5. GM5876070

    Engine Oil Cooler Pipe (2) @ Engine Oil Cooler Adapter - Install

  6. Retaining Clip (1) - Install
  7. GM5875991

    Radiator Outlet Hose (4) @ Engine Oil Cooler Adapter - Install

  8. Radiator Outlet Hose Clamp (3) @ Engine Oil Cooler Adapter - Engage - Hose Clamp Replacement Guidelines - Spring Type 
  9. Turbocharger Coolant Feed Lower Hose (2) @ Engine Oil Cooler Adapter - Install
  10. Turbocharger Coolant Feed Hose Clamp (1) @ Engine Oil Cooler Adapter - Engage - Hose Clamp Replacement Guidelines - Spring Type 
  11. GM5480146

    Electric Belt Drive Rack and Pinion Steering Gear (3) - Install

    12. CAUTION:

    This vehicle is equipped with torque-to-yield or single use fasteners. Install a NEW torque-to-yield or single use fastener when installing this component. Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component.

  12. Steering Gear Bolt (2) - Install NEW [2x]
  13. Steering Gear Nut (1) - Install and tighten [2x] - Fastener Specifications
  14. GM5316620

    Connect the electrical connectors (1).

  15. Secure the engine wiring harness to the electric belt drive rack and pinion steering gear using a tie strap.
  16. GM5479919

    Intermediate Steering Shaft (2) @ Electric Belt Drive Rack and Pinion Steering Gear - Install

  17. If a NEW threaded component is being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded component is reused, prepare the threaded component using the following steps:
    1. Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
    2. Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Apply thread locking adhesive to the external threads of the component. Adhesives, Fluids, Lubricants, and Sealers
    4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
  18. Intermediate Steering Shaft Lower Bolt (1) @ Electric Belt Drive Rack and Pinion Steering Gear - Install and tighten - Fastener Specifications
  19. GM4093212
    CAUTION:

    Ensure the Outer Tie Rod Boot is not twisted or deformed during assembly. If the boot is twisted or deformed, damage to the boot will occur.

    NOTE:

    Left side shown, right side similar.

    Install left and right steering linkage outer tie rods (1) at the left and right steering knuckles.

  20. GM5420203
    NOTE:
    • Left side shown, right side similar.
    • Some components not shown for graphic clarity.

    Install and tighten the left and right steering linkage outer tie rod nuts (1). Fastener Specifications

  21. GM5877068

    Install the front cradle sheer plate (2) between the front bumper fascia center air deflector and the driveline and front suspension cradle and raise into position.

  22. Ensure that the left and right side wheelhouse liners (1) are positioned in place under the front cradle sheer plate (2).
  23. Front Wheelhouse Liner Bolt (1) - Install and tighten [2x] - Fastener Specifications
  24. GM5877036

    Front Crossmember Brace Bolt (3) - Install and tighten [8x] - Fastener Specifications

  25. Front Cradle Shear Plate Nut (2) - Install and tighten [2x] - Fastener Specifications
  26. Front Cradle Shear Plate Bolt (1) - Install and tighten [4x] - Fastener Specifications
  27. Remove the jack.
  28. GM5862911

    Front Bumper Fascia Air Deflector Retainer (2) - Install

  29. Front Bumper Fascia Air Deflector Bolt (1) - Install and tighten [4x] - Fastener Specifications
  30. GM5876696
    NOTE:

    Left side shown, right side similar.

    Front Compartment Air Deflector- Left Side and Right Side (1) - Install

  31. GM5876673
    NOTE:

    Left side shown, right side similar.

    Front Bumper Fascia Lower Stiffener Bolt- Left Side and Right Side (3) - Install and tighten [6x] - Fastener Specifications

  32. Front Compartment Air Deflector Retainer- Left Side and Right Side (2) - Install [2x]
  33. Front Wheelhouse Liner Bolt- Left Side and Right Side (1) - Install and tighten [4x] - Fastener Specifications
  34. GM5873831
    NOTE:

    Left side shown, right side similar.

    Front Brake Rotor Cooling Duct Deflector (1)- Left Side and Right Side - Install

  35. Front Brake Rotor Cooling Duct Deflector Bolt (2)- Left Side and Right Side - Install and tighten [6x] - Fastener Specifications
  36. GM5873833
    NOTE:

    Left side shown, right side similar.

    Install the 4 chassis harness retainers (1) on the left and right side.

  37. Program the power steering control module. Control Module References
  38. Install the front tire and wheel assemblies. Tire and Wheel Removal and Installation
  39. Lower the vehicle.
  40. Measure and adjust the front toe. Wheel Alignment - Steering Wheel Angle and/or Front Toe Adjustment
  41. Perform the following so the vehicle software relearns the steering center position:
    1. Raise the front wheels off the ground.
    2. Start the vehicle.
    3. Rotate steering wheel to the left lock position and hold tightly for 4 seconds.
    4. Rotate steering wheel to the right lock position and hold tightly for 4 seconds.
    5. Repeat steps 41.3 and 41.4.
    6. Lower the vehicle.
scientia non olet · About LEMON Manuals