Installation Procedure
Cooling Fan Motor (1) - Install
- NOTE:
Some components not shown for graphic clarity.
CAUTION:Refer to Fastener Caution .
Engine Coolant Fan Bolt (1) - Install and tighten [4x] - Fastener Specifications
Electrical Connector (1) @ Cooling Fan Motor - Connect
Radiator Outlet Hose Clip (2) @ Cooling Fan Motor - Install
Radiator Outlet Hose Clip (3) @ Cooling Fan Motor - Install
- NOTE:
The left side front bumper fascia lower reinforcement is removed for illustration purposes only.
Radiator Air Lower Baffle (1) - Install
- Radiator Air Lower Baffle Retainer (2) - Install [6x]
Front Bumper Fascia Center Air Deflector (1) - Install
Front Bumper Fascia Air Deflector Retainer (2) - Install
- Front Bumper Fascia Air Deflector Bolt (1) - Install and tighten [4x] - Fastener Specifications
Front Bumper Fascia Center Air Deflector Bolt (1) - Install and tighten [8x] - Fastener Specifications
Front Bumper Fascia Center Air Deflector Bolt (1) - Install and tighten [6x] - Fastener Specifications .
Air Cleaner Assembly (2) - Install
- Air Cleaner Bolt (1) - Install and tighten - Fastener Specifications
- Install all retainers and wiring harnesses to the air cleaner assembly as necessary.
- Connect the 2 mass airflow sensor electrical connectors.
Auxiliary Air Cleaner Outlet Duct (4) - Install
- Air Cleaner Outlet Duct Clamp (3) - Tighten - Fastener Specifications
- Air Cleaner Outlet Duct (2) - Install
- Air Cleaner Outlet Duct Clamp (1) - Tighten - Fastener Specifications
- NOTE:
Left side shown, right side similar.
Front End Sheet Metal Cross Brace Bracket - Left Side and Right Side (1) - Install [2x]
- Install the forward lamp wire harness retainers to the left and right side front end sheet metal cross brace brackets.
- NOTE:
Left side shown, right side similar.
Front End Sheet Metal Diagonal Brace Bolt- Left Side and Right Side (1) - Install and tighten [6x] Fastener Specifications
- NOTE:
Left side shown, right side similar.
Front End Sheet Metal Cross Brace- Left Side and Right Side (3) - Install [2x]
- Front Suspension Strut Upper Mounting Nut- Left Side and Right Side (2) - Install and tighten [4x] - Fastener Specifications
- Front End Sheet Metal Cross Brace Bolt- Left Side and Right Side (1) - Install and tighten [6x] - Fastener Specifications
- Install all wiring harness retainers to the front end sheet metal cross braces.
Radiator Air Upper Baffle- Lower (2) - Install
- Radiator Air Upper Baffle Retainer (1) - [2x] Install
Radiator Air Upper Baffle- Upper (3) - Install
- Radiator Air Upper Baffle Bolt (2) - Install and tighten [2x] - Fastener Specifications
- Radiator Air Upper Baffle Retainer (1) - Install [5x]
Transmission Control Module (1) @ Engine Control Module Bracket (2) - Install
- Engine Control Module Bracket (2) - Install
Engine Control Module Bracket Bolt (1) - Install and tighten [3x] - Fastener Specifications
Engine Control Module (1) - Install
- Connect the electrical connectors.
Radiator Surge Tank Outlet Pipe (3) - Install
- Radiator Surge Tank Inlet Hose Clamp (4) @ Engine Radiator - Engage - Hose Clamp Replacement Guidelines - Spring Type
- Radiator Surge Tank Inlet Hose Clip (2) @ Engine Control Module Bracket - Install
- Radiator Surge Tank Inlet Hose Clamp (1) @ Radiator Surge Tank Inlet Hose - Engage - Hose Clamp Replacement Guidelines - Spring Type
- Remove the shop cloths from beneath the radiator surge tank outlet pipe.
- Fill the cooling system to the proper level. Refer to Cooling System Draining and Filling (LF4 Static Fill) , or Cooling System Draining and Filling (LF4 GE 47716)
- Connect the negative battery cable. Battery Negative Cable Disconnection and Connection
- Start the engine and check for coolant leaks.
Refer to Component Fastener Tightening Caution .