Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT5. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of GENERAL MOTORS COMPANY

NOTE:
Ensure that the rear suspension cradle is securely attached to the jack/support stand.

Using the GE-52200 Lifting Table, raise the rear suspension cradle 6 - 8 inches from the vehicle and install available electrical connectors and retainers.
Rear Suspension Cradle (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Install the CH-51034-A Cradle Alignment Pins (1) to align the rear cradle to the body.
Courtesy of GENERAL MOTORS COMPANY

CAUTION:
Refer to Fastener Caution .

Rear Suspension Cradle Front Bolt (2) - Install NEW and hand tighten [2x]

CAUTION:

Refer to Torque-to-Yield Fastener Caution .

Rear Suspension Cradle Rear Bolt (1) Install NEW and tighten [2x]
1. First Pass: 100 N.m (74 lb ft)
2. Final Pass: (90 - 105 degrees)
Remove the GE-52200 Lifting Table from under the vehicle.
Remove the jack stand(s) from the front of the vehicle.
Courtesy of GENERAL MOTORS COMPANY

Using a suitable jack stand (1), support the differential carrier.
Courtesy of GENERAL MOTORS COMPANY

Position a block of wood (1) and a suitable jack stand (2) between the frame of the vehicle and the left rear suspension bracket.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
DO NOT raise the vehicle higher than necessary.

Using the block of wood and a suitable jack stand (1), raise the vehicle just enough to reposition the hoist pad (2) from under the vehicle.

DO NOT ATTEMPT OTHER REPAIRS WITH JACK STANDS IN PLACE.
Courtesy of GENERAL MOTORS COMPANY

Rear Suspension Cradle Front Bolt - Left Side (1) - Remove
Courtesy of GENERAL MOTORS COMPANY

Install the left rear suspension bracket. Rear Suspension Bracket Replacement - Front
Courtesy of GENERAL MOTORS COMPANY

Reposition the hoist lift pad (2) back underneath the vehicle.
Using the jack stand (1) and the block of wood, slowly lower the vehicle back on the hoist pad (2).
Courtesy of GENERAL MOTORS COMPANY

Remove the jack stand (2) and the block of wood (1) from underneath the vehicle.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Position a block of wood (1) and a suitable jack stand (2) between the frame of the vehicle and the right rear suspension bracket.
Courtesy of GENERAL MOTORS COMPANY
NOTE:
- Left side shown, right side similar.
- DO NOT raise the vehicle higher than necessary.
Using the block of wood and a suitable jack stand (1), raise the vehicle just enough to reposition the hoist pad (2) from under the vehicle.

DO NOT ATTEMPT OTHER REPAIRS WITH JACK STANDS IN PLACE.
Courtesy of GENERAL MOTORS COMPANY

Rear Suspension Cradle Front Bolt - Right Side (1) - Remove
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Install the right rear suspension bracket. Rear Suspension Bracket Replacement - Front
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Reposition the hoist lift pad (2) back underneath the vehicle.
Using the jack stand (1) and the block of wood, slowly lower the vehicle back on the hoist pad (2).
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Remove the jack stand (2) and the block of wood (1) from underneath the vehicle.
Courtesy of GENERAL MOTORS COMPANY

Remove the jack stand (1) supporting the differential carrier.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Install the left and right rear suspension brackets. Rear Suspension Bracket Replacement - Rear
Remove the suitable jack/support stand.
Reposition and connect the wiring harness to the rear cradle as necessary.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Install the left and right rear brake caliper brackets and brake calipers (2) as assemblies.
Rear Brake Caliper Bracket Bolt - Left Side and Right Side (1) - Install and tighten [4x] - Rear Brake Caliper Bracket Replacement
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Rear Brake Hose Clip Bolt - Left Side and Right Side (1) @ Rear Suspension Upper Control Arm - Install and tighten - Rear Brake Hose Replacement (J56, JL9) , or Rear Brake Hose Replacement (J6H) , or Rear Brake Hose Replacement (J57)
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Rear Suspension Lower Control Arm - Left Side and Right Side (1) - Install [2x] - Rear Suspension Lower Control Arm Replacement
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Rear Suspension Upper Trailing Link - Left Side and Right Side (1) - Install [2x] - Rear Suspension Upper Trailing Link Replacement (FE2, FE3) , or Rear Suspension Upper Trailing Link Replacement (FE4)
Courtesy of GENERAL MOTORS COMPANY

Propeller Shaft (1) - Install - Propeller Shaft Replacement (without LT4) , or Propeller Shaft Replacement (AWD)

NOTE:

Vehicle alignment is not required if cradle is being lowered or dropped to perform another procedure. This vehicle is equipped with a cradle to body aligning feature: cradle to body through holes or self-aligning pins that are part of cradle or body. Only align if replacing the cradle with new part and transferring components.

Measure and adjust the wheel alignment. Wheel Alignment Measurement