LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 158 (Engine Mechanical - 2.7L (L3B) - Repair Instructions (1 Of 3)) >> Repair Instructions >> Engine Support Fixture >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disconnect the battery. Battery Negative Cable Disconnection and Connection
  2. GM5325063

    Using the appropriate trim tool, remove the windshield wiper arm finish cap (1) from the windshield wiper arm (3).

  3. Windshield Wiper Arm Nut (2) - Remove
  4. Grasp the outer end of the windshield wiper arm (3) and gently rock the arm back and forth to remove it from the windshield wiper transmission pivot shaft.
  5. GM5417116

    Apply two layers of masking tape around the top edge of the service part to prevent paint damage.

  6. Using a suitable plastic trim tool, carefully release the air inlet grille panel extension clips.
  7. Remove the air inlet grille panel extension (1) from the air inlet grille panel and upper front fender.
  8. GM5421986

    Remove the 2 hood rear outer air inlet seal retainer (1) from the left and right side.

  9. Remove the hood rear outer air inlet seal (2) from the left and right side.
  10. GM5421990

    Remove the 2 front compartment side sight shield retainer (1) from the left and right side.

  11. Remove the front compartment side sight shield (2) from the left and right side.
  12. GM5417442

    Air Inlet Grille Panel Retainer (1) - Remove [6x]

  13. Disconnect the windshield washer nozzle hose from the windshield washer pump hose.
  14. Lift the front edge of the air inlet grille panel (2) and slide the panel forward from both hood hinges to remove.
  15. GM5420286

    Windshield Wiper System Module Shield (1) - Remove

  16. GM5420344

    Disconnect the windshield wiper motor electrical connector.

  17. Windshield Wiper System Module Bolt (1) - Remove [2x]
  18. Slide the windshield wiper system module (2) inboard to release the grommet from the plenum and remove the windshield wiper system module (2) from the vehicle.
  19. GM5499581

    Air Inlet Deflector Water Deflector Retainer (1) - Remove [2x]

  20. GM5499583

    Air Inlet Deflector Water Deflector (1) - Remove

  21. GM5422039

    Plenum Front Panel Nut (1) - Remove [3x]

  22. Plenum Front Panel Bolt (2) - Remove [3x]
  23. Pull the forward lamp wiring harness extension (3) out from the plenum front panel.
  24. GM5422041

    Plenum Front Panel Bolt (1) - Remove [4x]

  25. Plenum Front Panel Nut (2) - Remove [3x]
  26. Pull the forward lamp wiring harness extension (3) out from the plenum front panel.
  27. GM5422044

    Plenum Front Panel (1) - Remove

  28. GM5478556

    Hood Hinge Nut (1) - Remove [4x]

  29. With the aid of an assistant, remove the hood (2).
  30. GM5420297

    Radiator Air Upper Baffle Retainer (1) - Remove [7x]

  31. Radiator Air Upper Baffle (2) - Remove
  32. Remove the oil fill cap.
  33. GM5432171

    Intake Manifold Cover Bolt (1) - Remove [2x]

  34. Lift up on the front of the intake manifold cover (2).
  35. GM5432174

    Intake Manifold Cover (1) @ Upper Intake Manifold Bracket (2) - Remove

  36. GM5323001

    EN-36857  Engine Lift Bracket Set (1) - Install

    37. CAUTION:

    Refer to Fastener Caution .

  37. EN-51768  Engine Support Fixture Adapter Bolts- M8 (2) - Install and tighten 65 N.m (48 lb ft)
  38. GM5598887

    EN-36857  Engine Lift Bracket Set (1) - Install

  39. EN-51768  Engine Support Fixture Adapter Bolts- M8 (2) - Install and tighten 65 N.m (48 lb ft)
  40. GM5598930
    NOTE:

    Ensure that the engine support fixture only contacts the frame. Do not install on top of fender lip.

    EN-51007  Global Engine Support Fixture (1) - Install

scientia non olet · About LEMON Manuals