Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.

Crankshaft Balancer (2) - Install

Prepare the NEW Crankshaft Balancer Bolt (1) for installation as follows.
1. Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
2. Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
3. Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
4. Ensure there are no gaps in the thread locking adhesive once applied to the component.

CAUTION:

Refer to Fastener Caution .

Crankshaft Balancer Bolt - Install NEW and tighten - Fastener Specifications
EN-52476 Flywheel Holding Tool (2) - Remove
Auxiliary Generator Battery Jumper Cable (2) - Install
Battery Positive Cable Nut (1) @ Starter Solenoid - Install and tighten - Fastener Specifications
Electrical Connector (4) - Connect
Starter (3) - Install
Starter Bolt (2) - Install and tighten [2x] - Fastener Specifications
Starter Stud (1) - Install and tighten - Fastener Specifications
Auxiliary Generator Battery Jumper Cable (2) - Install
Auxiliary Generator Battery Jumper Cable Terminal Nut (1) - Install and tighten - Fastener Specifications
Retainer (3) - Engage
Engine Oil Cooler Seal (2) - Install NEW [2x]
Engine Oil Cooler (1) - Install
Engine Oil Cooler Bolt (1) - Install and tighten [4x] - Fastener Specifications
Engine Oil Cooler Coolant Inlet Hose (3) @ Engine Oil Cooler - Install
Engine Oil Cooler Coolant Outlet Hose (2) @ Engine Oil Cooler - Install
Hose Clamp (1) - Engage [2x] - Hose Clamp Replacement Guidelines - Spring Type
Lower the vehicle.
Fill the engine oil to the proper level with NEW engine oil. Engine Oil and Oil Filter Replacement (RWD)
Fill the cooling system. Refer to Cooling System Draining and Filling (L3B Static Fill) , or Cooling System Draining and Filling (L3B GE 47716)
Front Compartment Air Deflector (1) - Install
CAUTION:
Refer to Fastener Caution

NOTE:
Quantity of fasteners may vary based on option content.

Front Compartment Air Deflector Bolt (1) - Install and tighten [6x] - Fastener Specifications
NOTE:
Quantity of fasteners may vary based on option content.

Front Wheelhouse Liner Bolt (3) - Install and tighten - Fastener Specifications
Engine Front Splash Shield Retainer (2) - Install and tighten
Engine Front Splash Shield Bolt (1) - Install and tighten - Fastener Specifications
NOTE:
Quantity of fasteners may vary based on option content.

Front Wheelhouse Liner Bolt (1) - Install and tighten - Fastener Specifications
Engine Front Splash Shield Retainer (2) - Install
Engine Front Splash Shield Bolt (3) - Install and tighten - Fastener Specifications
Front Bumper Fascia Center Air Deflector Bolt (1) - Install and tighten [5x] - Fastener Specifications
Front Bumper Fascia Center Air Deflector Retainer (2) - Install [2x]
Lower the vehicle. Lifting and Jacking the Vehicle
Position the accessory drive primary belt onto all of the pulleys except one idler pulley.
Use a suitable tool to rotate the drive belt tensioner (1) counterclockwise and hold.
Accessory Drive Primary Belt (2) - Install
Release the drive belt tensioner, inspect the accessory drive primary belt (2) to ensure it is centered on all pulleys.
Intake Manifold Cover (1) @ Upper Intake Manifold Bracket (2) - Install
Push down on the front of the intake manifold cover (2).
Intake Manifold Cover Bolt (1) - Install [2x] - Fastener Specifications
Install the oil fill cap.
Battery Negative Cable - Connect - - Battery Negative Cable Disconnection and Connection