LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 136 (Engine Mechanical - 3.6L (LF4) - Repair Instructions (2 Of 4)) >> Repair Instructions >> Camshaft Position Actuator Replacement - Bank 2 (Left Side) Intake >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5896820
    NOTE:

    Ensure the proper camshaft position actuator is installed in the correct position. The dowel pin on the camshaft position actuator must be aligned with the slot in the camshaft nose for reassembly. Failure to install the proper camshaft position actuator can effect engine performance and set an engine code.

    Install the camshaft position actuator (1) by inserting the actuator between the timing chain and front cover. While pushing the actuator into the tensioned side of the chain, tilt the actuator while engaging the chain, aligning the marks on the chain and place the actuator in the fully seated position.

  2. Carefully pry the camshaft forward and move the to reengage the position actuator to the camshaft. The dowel pin on the camshaft position actuator must be aligned with the slot in the camshaft nose for reassembly.
  3. GM5896809

    Camshaft Position Actuator Bolt (1) - Install and hand tighten

  4. GM5896415
    NOTE:

    Some components not shown for graphic clarity.

    Loosen the EN-48313  Timing Chain Retention Tool (1) and remove the EN-48313  Timing Chain Retention Tool (2).

  5. GM5896809
    CAUTION:

    Refer to Fastener Caution .

    Camshaft Position Actuator Bolt (1) - Install and tighten - Fastener Specifications

  6. GM5892401

    Camshaft Bearing Cap (2) - Install

  7. Camshaft Bearing Cap Bolt (1) - Install and hand tighten [4x] - Fastener Specifications
  8. GM5839247

    Camshaft Position Actuator Solenoid Valve (2) - Install

  9. Camshaft Position Actuator Solenoid Valve Bolt (1) - Install and tighten - Fastener Specifications
  10. Connect the electrical connector.
  11. GM5839194

    Camshaft Position Actuator Solenoid Valve (2) - Install

  12. Camshaft Position Actuator Solenoid Valve Bolt (1) - Install and tighten - Fastener Specifications
  13. Connect the electrical connector.
  14. GM5838696

    Camshaft Position Sensor (2) - Install

  15. Camshaft Position Sensor Bolt (1) - Install and tighten - Fastener Specifications
  16. Connect the electrical connector.
  17. GM5838611

    Camshaft Position Sensor (2) - Install

  18. Camshaft Position Sensor Bolt (1) - Install and tighten - Fastener Specifications
  19. Connect the electrical connector.
  20. GM5869205
    NOTE:

    Some components not shown for graphic clarity.

    Apply RTV silicone sealant on the engine front cover split lines (1). The required thickness of the sealing bead is 8 mm (0.3150 in) by 4 mm (0.1575 in). Adhesives, Fluids, Lubricants, and Sealers

  21. GM5869076
    NOTE:

    Some components not shown for graphic clarity.

    Camshaft Cover Seal (2) - Install NEW

  22. Camshaft Cover (1) - Install
  23. GM5869075
    NOTE:

    Some components not shown for graphic clarity.

    Camshaft Housing Cover Bolt (1) - Install and tighten in sequence [15x] - Fastener Specifications

  24. GM5869085

    Remove the 3 EN-46101  Spark Plug Tube Seal Guides (1).

  25. GM5869074
    NOTE:

    Some components not shown for graphic clarity.

    Engine Wiring Harness (3) - Install

  26. Engine Wiring Harness Retainer (2) - Install [10x]
  27. Electrical Connector (1) - Connect
  28. GM5861168

    Ignition Coil (2) - Install

  29. Ignition Coil Bolt (1) - Install and tighten - Fastener Specifications
  30. Connect the electrical connectors.
  31. GM5861042

    Air Cleaner Outlet Resonator Bracket (1) - Install

  32. GM5861039

    Oil Level Indicator Tube (3) - Install

  33. Retainer (2) - Install [2x]
  34. Air Cleaner Outlet Duct Bracket Bolt (1) - Install and tighten [2x] - Fastener Specifications
  35. GM5860358

    Auxiliary Air Cleaner Outlet Duct (1) - Install

  36. GM5860357

    Retainer Spring (3) - Engage

  37. Charge Air Bypass Valve Hose (2) - Install
  38. Charge Air Bypass Valve Hose Clamp (1) - Tighten - Fastener Specifications
  39. GM5860356

    Air Cleaner Outlet Duct Clamp (2) - Tighten - Fastener Specifications

  40. Turbocharger Wastegate Actuator Vacuum Tank Solenoid Valve Tube (1) - Connect - Plastic Collar Quick Connect Fitting Service
  41. GM5846598

    Install the NEW positive crankcase ventilation fresh air tube (2) and secure the 2 positive crankcase ventilation tube connectors (1).

  42. GM5864683

    Lower Intake Manifold Gasket (2) - Install NEW [6x]

  43. Intake Manifold (1) - Install
  44. GM5864681

    If a NEW threaded component is being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded component is reused, prepare the threaded component using the following steps:

    1. Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
    2. Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Remove loose debris from internal and external threads using compressed air.
    4. Apply liquid thread locking adhesive in a strip along half of the length of the external threads, starting at the tip, just prior to installation. Adhesives, Fluids, Lubricants, and Sealers
  45. Lower Intake Manifold Bolt (1) - Install and tighten in sequence [6x] - Fastener Specifications
  46. Connect all electrical connectors.
  47. GM5862841
    NOTE:

    Some components not shown for graphic clarity.

    Positive Crankcase Ventilation Foul Air Tube (2) - Install

  48. Positive Crankcase Ventilation Tube Connector (1) - Connect [2x] - Plastic Collar Quick Connect Fitting Service
  49. GM4044075

    Fuel Pipe Shield (1) - Install

  50. GM5869276

    Wiring Harness (3) - Install

  51. Wiring Harness Retainer (2) - Install [3x]
  52. Engine Rear Noise Shield Bolt (1) - Install and tighten [2x] - Fastener Specifications
  53. GM4044046

    Engine Rear Noise Shield Bolt (1) - Install and tighten - Fastener Specifications

  54. GM5862663
    NOTE:

    Some components not shown for graphic clarity.

    Charge Air Cooler Cover Seal (3) - Install NEW [2x]

  55. Intake Manifold Gasket (2) - Install NEW
  56. Charge Air Cooler Cover (1) - Install
  57. GM5862662
    NOTE:

    Some components not shown for graphic clarity.

    Charge Air Cooler Cover Bolt (2) - Install and hand tighten [12x]

  58. Charge Air Cooler Bolt (1) - Install and hand tighten [2x]
  59. Charge Air Cooler Bolt (1) & Charge Air Cooler Cover Bolt [2x] - Tighten in sequence [14x] - Fastener Specifications
  60. Connect the electrical connectors.
  61. GM5840540

    Charge Air Cooler Inlet Air Tube Seal (4) - Install NEW

  62. Charge Air Cooler Inlet Pipe (3) - Install
  63. Charge Air Bypass Valve Tube Connector Clamp (2) - Tighten - Fastener Specifications
  64. Charge Air Cooler Inlet Air Tube Bolt (1) - Install and tighten [2x] - Fastener Specifications
  65. GM5840576

    Charge Air Cooler Inlet Air Tube Seal (4) - Install NEW

  66. Charge Air Cooler Inlet Pipe (3) - Install
  67. Charge Air Bypass Valve Tube Connector Clamp (2) - Tighten - Fastener Specifications
  68. Charge Air Cooler Inlet Air Tube Bolt (1) - Install and tighten [2x] - Fastener Specifications
  69. GM5860462

    Charge Air Cooler Coolant Hose (1) @ Supercharger Water Manifold - Install

  70. Charge Air Cooler Coolant Hose Clamp (2) - Engage - Hose Clamp Replacement Guidelines - Spring Type
  71. Charge Air Cooler Coolant Hose Retainer (3) @ Charge Air Cooler Coolant Outlet Pipe Bracket - Install
  72. GM5854975

    Charge Air Cooler Coolant Hose (2) @ Supercharger Water Manifold - Install

  73. Charge Air Cooler Coolant Hose Clamp (3) - Engage - Hose Clamp Replacement Guidelines - Spring Type
  74. Charge Air Cooler Coolant Hose Retainer (1) @ Charge Air Cooler Coolant Outlet Pipe Bracket - Install [2x]
  75. GM4057738

    Turbocharger Wastegate Actuator Vacuum Tank (2) - Install

  76. Turbocharger Wastegate Actuator Vacuum Tank Bolt (1) - Install and tighten [2x] - Fastener Specifications
  77. GM4057709

    Electrical Connector (1) @ Charge Air Bypass Valve (2) - Connect

  78. GM4057618

    Charge Air Bypass Valve Tube (1) @ Charge Air Bypass Valve - Connect - Plastic Collar Quick Connect Fitting Service

  79. GM4057453

    Electrical Connector (1) @ Charge Air Bypass Valve (2) - Connect

  80. GM4057385

    Charge Air Bypass Valve Tube (1) @ Charge Air Bypass Valve - Connect - Plastic Collar Quick Connect Fitting Service

  81. GM4057362

    Turbocharger Wastegate Actuator Vacuum Source Tube (1) @ Vacuum Pump - Connect - Plastic Collar Quick Connect Fitting Service

  82. GM4052248

    Charge Air Bypass Valve Vacuum Tank Tube (3) - Connect - Plastic Collar Quick Connect Fitting Service

  83. GM5839308

    Turbocharger Wastegate Actuator Vacuum Tank Solenoid Valve Tube (3) @ Auxiliary Air Cleaner Outlet Duct - Connect - Plastic Collar Quick Connect Fitting Service

  84. GM5839386

    Turbocharger Wastegate Actuator Vacuum Tank Bolt (3) - Install and tighten [2x] - Fastener Specifications

  85. GM5839336

    Turbocharger Wastegate Actuator Vacuum Tank Bolt (3) - Install and tighten [2x] - Fastener Specifications

  86. Connect the electrical connectors.
  87. GM5842421

    Evaporative Emission Canister Purge Tube (1) - Install

  88. Evaporative Emission Canister Purge Tube (1) - Connect [2x] - Plastic Collar Quick Connect Fitting Service
  89. GM5862960

    Air Cleaner Assembly (2) - Install

  90. Air Cleaner Bolt (1) - Install and tighten - Fastener Specifications
  91. Install all retainers and wiring harnesses to the air cleaner assembly as necessary.
  92. Connect the 2 mass airflow sensor electrical connectors.
  93. GM5864667

    Auxiliary Air Cleaner Outlet Duct (4) - Install

  94. Air Cleaner Outlet Duct Clamp (3) - Tighten - Fastener Specifications
  95. Air Cleaner Outlet Duct (2) - Install
  96. Air Cleaner Outlet Duct Clamp (1) - Tighten - Fastener Specifications
  97. GM5839283

    Oil Filler Cap - Remove

  98. Intake Manifold Cover (2) - Install
  99. Intake Manifold Cover Bolt (1) - Install and tighten - Fastener Specifications
  100. Oil Filler Cap - Install
  101. GM5872932

    Front End Sheet Metal Diagonal Brace- Left Side (3) - Install

  102. Front End Sheet Metal Cross Brace Bolt- Left Side (2) - Install and tighten - Fastener Specifications
  103. Front End Sheet Metal Diagonal Brace Nut- Left Side (1) - Install and tighten - Fastener Specifications
  104. GM5839407

    Front End Sheet Metal Cross Brace- Left Side (3) - Install

  105. Install the engine wire harness retainers to the front end sheet metal cross brace.
  106. Front Suspension Strut Upper Mounting Nut- Left Side (2) - Install and tighten [2x] - Fastener Specifications
  107. Front End Sheet Metal Cross Brace Bolt- Left Side (1) - Install and tighten [3x] - Fastener Specifications
  108. GM5864524

    Radiator Air Upper Baffle (3) - Install

  109. Radiator Air Upper Baffle Bolt (2) - Install and tighten [2x] - Fastener Specifications
  110. Radiator Air Upper Baffle Retainer (1) - Install [5x]
  111. GM5865881

    Plenum Front Panel (1) - Install - Plenum Front Panel Removal and Installation (with Blackwing) , or Plenum Front Panel Removal and Installation (without Blackwing)

  112. Fill the charge air cooling system. Refer to Cooling System Draining and Filling (LF4 Static Fill) , or Cooling System Draining and Filling (LF4 GE 47716)
scientia non olet · About LEMON Manuals