Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of GENERAL MOTORS COMPANY

Transmission Fluid Cooler Seal (2) - Install NEW
Transmission Fluid Cooler Thermal Bypass Valve Gasket (1) - Install NEW [2x]
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Remove the caps from the fittings and plugs from the holes before installing the transmission fluid cooler pipes.

Transmission Fluid Cooler Inlet and Outlet Pipe (2) - Install

CAUTION:

Refer to Fastener Caution .

Transmission Fluid Cooler Pipe Nut (1) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Transmission Fluid Cooler Pipe Nut (2) - Install and tighten - Fastener Specifications
Transmission Fluid Cooler Pipe Clip Bolt (1) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Charge Air Cooler Inlet Air Tube (2) @ Charge Air Cooler (3) - Install
Retainer Spring (1) - Engage
Courtesy of GENERAL MOTORS COMPANY

Charge Air Cooler Inlet Air Tube (2) @ Turbocharger (3) - Install
Retainer Spring (1) - Engage
Courtesy of GENERAL MOTORS COMPANY

Radiator Air Upper Baffle (2) - Install
Radiator Air Upper Baffle Retainer (1) - Install [7x]
Courtesy of GENERAL MOTORS COMPANY

Install the radiator air side baffle (1) by manipulating it between the vehicle components and beneath the radiator air upper baffle.
Courtesy of GENERAL MOTORS COMPANY

Radiator Air Seal Retainer (2) - Install [2x]
Radiator Air Upper Baffle Retainer (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Install the air cleaner (1) and air cleaner outlet duct (2) as an assembly.
Courtesy of GENERAL MOTORS COMPANY

Air Cleaner Outlet Duct Clamp (2) - Tighten - Fastener Specifications
Air Cleaner Bolt (1) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Electrical Connector (4) - Connect [2x]
Evaporative Emission Canister Purge Tube (3) - Connect - Plastic Collar Quick Connect Fitting Service
Positive Crankcase Ventilation Tube (2) - Connect - Plastic Collar Quick Connect Fitting Service
Wiring Harness Retainer (1) @ Air Cleaner Assembly - Install [3x]
Courtesy of GENERAL MOTORS COMPANY

Radiator Upper Bracket (3) - Install
Radiator Upper Bracket Bolt (2) - Install and tighten [2x] - Fastener Specifications
Wiring Harness Retainer (1) - Install
Raise the vehicle.
Courtesy of GENERAL MOTORS COMPANY

Radiator Air Seal Retainer (1) - Install [2x]
Courtesy of GENERAL MOTORS COMPANY

Radiator Air Front Lower Baffle (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Radiator Air Front Lower Baffle Retainer (1) - Install [3x]
Courtesy of GENERAL MOTORS COMPANY

Radiator Air Lower Baffle (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Radiator Air Lower Baffle Retainer (2) - Install
Radiator Air Lower Seal Retainer (1) - Install [6x]
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Center Air Deflector (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Center Air Deflector Retainer (3) - Install [2x]
Front Bumper Fascia Center Air Deflector Bolt (2) - Install and tighten - Fastener Specifications
Front Bumper Fascia Center Air Deflector Screw (1) - Install and tighten [6x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Center Air Deflector Screw (1) - Install and tighten [10x] - Fastener Specifications .
Lower the vehicle.
Courtesy of GENERAL MOTORS COMPANY

Intake Manifold Cover (1) @ Upper Intake Manifold Bracket (2) - Install
Courtesy of GENERAL MOTORS COMPANY

Push down on the front of the intake manifold cover (2).
Intake Manifold Cover Bolt (1) - Install and tighten [2x] - Fastener Specifications
Install the oil fill cap.
Check the transmission fluid level. Transmission Fluid Level and Condition Check
Inspect for transmission fluid leaks. Fluid Leak Diagnosis