LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 101 (Transmission Cooling System) >> Repair Instructions >> Automatic Transmission Fluid Cooling Exchanger Replacement (L3B, AWD) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5485960Courtesy of GENERAL MOTORS COMPANY

    Automatic Transmission Fluid Cooling Exchanger (2) - Install

    2. CAUTION:

    Refer to Fastener Caution .

  2. Automatic Transmission Fluid Cooling Exchanger Bolt (1) - Install and tighten [3x] - Fastener Specifications 
  3. GM5485959Courtesy of GENERAL MOTORS COMPANY

    Transmission Fluid Cooler Pipe Seal (1) - Install NEW [2x]

  4. GM5485958Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Remove the caps from the fittings and plugs from the holes before installing the transmission fluid cooler pipes.

    Transmission Fluid Cooler Inlet and Outlet Pipe (2) @ Automatic Transmission Fluid Cooling Exchanger - Install

  5. Transmission Fluid Cooler Pipe Connector Bolt (1) - Install and tighten [2x] - Fastener Specifications 
  6. GM5485957Courtesy of GENERAL MOTORS COMPANY

    Automatic Transmission Fluid Cooling Heat Exchanger Outlet Hose (4) @ Automatic Transmission Fluid Cooling Exchanger - Install

  7. Automatic Transmission Fluid Cooling Heat Exchanger Outlet Hose Clamp (3) - Engage - Hose Clamp Replacement Guidelines - Spring Type
  8. Automatic Transmission Fluid Cooling Heat Exchanger Inlet Hose (2) @ Automatic Transmission Fluid Cooling Exchanger - Install
  9. Automatic Transmission Fluid Cooling Heat Exchanger Inlet Hose Clamp (1) - Engage - Hose Clamp Replacement Guidelines - Spring Type
  10. GM5485767Courtesy of GENERAL MOTORS COMPANY

    Transmission Fluid Cooler Thermal Bypass Valve Gasket (2) - Install NEW [4x]

  11. GM5485765Courtesy of GENERAL MOTORS COMPANY

    Transmission Cooler Bypass Valve (2) - Install

  12. Transmission Fluid Cooler Thermal Bypass Valve Bolt (1) - Install and tighten - Fastener Specifications 
  13. GM5485764Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Remove the caps from the fittings and plugs from the holes before installing the transmission fluid cooler pipes.

    Transmission Fluid Cooler Inlet and Outlet Pipe (2) @ Transmission Cooler Bypass Valve - Install

  14. Transmission Fluid Cooler Pipe Bracket Nut (1) - Install and tighten - Fastener Specifications 
  15. GM5485763Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Remove the caps from the fittings and plugs from the holes before installing the transmission fluid cooler pipes.

    Transmission Fluid Cooler Inlet and Outlet Pipe (2) @ Transmission Cooler Bypass Valve - Install

  16. Transmission Fluid Cooler Pipe Bracket Nut (1) - Install and tighten - Fastener Specifications 
  17. Lower the vehicle.
  18. Fill the cooling system. Cooling System Draining and Filling (LSY GE 47716) , or Cooling System Draining and Filling (LSY Static Fill) , or Cooling System Draining and Filling (LSY with V03 Static Fill) , or Cooling System Draining and Filling (L3B Static Fill) , or Cooling System Draining and Filling (L3B GE 47716) , or Cooling System Draining and Filling (LSY with V03 GE 47716) , or Cooling System Draining and Filling (LF4 Static Fill) , or Cooling System Draining and Filling (LF4 GE 47716)
  19. Check the cooling system for leaks.
  20. Check the transmission fluid level. Transmission Fluid Level and Condition Check
  21. Inspect for transmission fluid leaks. Fluid Leak Diagnosis
scientia non olet · About LEMON Manuals