LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 60 (Engine Controls And Fuel - 2.7L (L3B) - Repair Instructions) >> Repair Instructions >> Throttle Inlet Absolute Pressure Sensor Replacement >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. Raise and support the vehicle. Lifting and Jacking the Vehicle
  2. GM5440604

    Front Wheelhouse Liner Bolt- Left Side (1) - Remove [4x]

  3. Front Tire Front Air Deflector Bolt- Left Side (2) - Remove
  4. Front Bumper Fascia Bolt- Left Side (3) - Remove [2x]
  5. GM5440606

    Reposition the left front wheelhouse liner (1) to gain access to the left side upper front bumper fascia bolt (2).

  6. Remove the left side upper front bumper fascia bolt (2).
  7. GM5440607

    Front Wheelhouse Liner Bolt- Right Side (1) - Remove [4x]

  8. Front Tire Front Air Deflector Bolt- Right Side (2) - Remove
  9. Front Bumper Fascia Bolt- Right Side (3) - Remove [2x]
  10. GM5440608

    Reposition the right front wheelhouse liner (1) to gain access to the right side upper front bumper fascia bolt (2).

  11. Remove the right side upper front bumper fascia bolt (2).
  12. GM5440610

    Front Bumper Fascia Center Air Deflector Screw (1) - Remove [10x]

  13. Remove the support and lower the vehicle.
  14. GM5440611

    Front Bumper Fascia Bolt (1) - Remove [6x]

  15. GM5440612

    On the right side of the front bumper fascia carefully push a small nylon wedge between the front bumper fascia (1), the front bumper fascia guide (2), and the front headlamp (3). Insert a suitable flat-bladed plastic trim tool into the fascia slot and depress the snaps one at a time and pull on the fascia at the same time to gradually remove the right side of the front bumper fascia.

  16. GM5440613

    Reposition the front bumper fascia on the right side to gain access to the electrical connector (1).

  17. Disconnect the electrical connector.
  18. GM5440614

    On the left side of the front bumper fascia carefully push a small nylon wedge between the front bumper fascia (1), the front bumper fascia guide (2), and the front headlamp (3). Insert a suitable flat-bladed plastic trim tool into the fascia slot and depress the snaps one at a time and pull on the fascia at the same time to gradually remove the left side of the front bumper fascia.

  19. GM5408645

    Front Bumper Fascia (1) - Remove

  20. GM5481342

    Auxiliary Radiator Duct Retainer (1) - Remove [3x]

  21. GM5481344

    Auxiliary Radiator Duct Retainer (1) - Remove [2x]

  22. GM5410889
    NOTE:

    The front bumper fascia support brace (2) may have a forward range radar sensor attached, if equipped.

    Front Bumper Fascia Support Brace Bolt (1) - Remove [3x]

  23. Front Bumper Fascia Support Brace (2) - Remove
  24. Disconnect the electrical connector from the forward range radar sensor, if equipped.
  25. GM5518513

    Intake Air Duct Retainer (1) - Remove [2x]

  26. Radiator Air Lower Seal Retainer (2) - Remove [2x]
  27. Radiator Air Lower Baffle Retainer (3) - Remove [2x]
  28. GM5422202

    Front End Sheet Metal Cross Brace Bolt (1) - Remove [4x]

  29. Front End Sheet Metal Cross Brace (2) - Remove [2x]
  30. GM5485943

    Horn Bolt (1) - Remove [2x]

  31. Horn (2) - Reposition [2x]
  32. GM5412380

    Reposition the wiring harness.

  33. Front Bumper Impact Bar Bolt (1) - Remove [8x]
  34. Front Bumper Impact Bar (2) - Remove
  35. GM5481345

    Auxiliary Radiator Front Duct (1) - Remove

  36. GM5399153

    Throttle Inlet Absolute Pressure Sensor Bolt (1) - Remove

  37. Throttle Inlet Absolute Pressure Sensor (2) - Remove
scientia non olet · About LEMON Manuals