LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 58 (Hydraulic Brakes - Repair Instructions) >> Repair Instructions >> Brake Pedal Removal and Installation (without MG9) >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disable the SIR system. SIR Disabling and Enabling
  2. GM5443235

    Instrument Panel Lower Airbag Nut (1) - Remove [2x]

  3. Instrument Panel Lower Airbag - Driver Side (2) - Remove
  4. Disconnect the electrical connector.
  5. GM5421735

    With a flat bladed plastic trim tool, start at the front and work your way back to release the clips.

  6. Instrument Panel Outer Trim Cover - Left Side (1) - Remove
  7. GM5300282

    Disconnect the hood primary latch release cable end retainer from the hood primary latch release cable handle (1).

  8. GM5310877

    Instrument Panel Lower Trim Panel Insulator Retainer (1) - Remove

  9. Instrument Panel Insulator Bolt (2) - Remove [2x]
  10. Instrument Panel Insulator Nut (3) - Remove [2x]
  11. GM5310878
    NOTE:

    Use a plastic trim tool if necessary.

    Release the tabs from the instrument panel lower trim panel insulator (1).

  12. GM5310879

    Instrument Panel Lower Trim Panel Insulator (1) - Remove

  13. Disconnect the electrical connector.
  14. GM5433957

    Move the steering column up so you can access the lower left corner of the instrument panel center trim pad (1).

  15. Start with a flat-bladed plastic trim tool in the lower left corner of the instrument panel center trim pad (1) and work your way clockwise.
  16. Instrument Panel Center Trim Pad (1) - Remove
  17. Disconnect the electrical connector.
  18. GM5446424

    Data Link Connector Bolt (1) - Remove [2x]

  19. Instrument Panel Knee Bolster Bolt (2) - Remove [3x]
  20. GM5446428

    Release the clips with a suitable tool.

  21. Disconnect and reposition harness as necessary.
  22. Clear the instrument panel knee bolster deflector studs when removing the instrument panel knee bolster (1).
  23. GM5325852

    Floor Front Air Outlet Duct Bolt (1) - Remove

  24. Floor Front Air Outlet Duct - Left Side Outer (2) - Remove
  25. GM5454049

    Instrument Panel Tie Bar Brace Bolt (1) - Remove [3x]

  26. Instrument Panel Knee Bolster Deflector (2) - Remove
  27. GM5454224
    NOTE:

    Typical wiring harness shown. Individual wiring harnesses may differ based on option content.

    Disconnect the electrical connectors. (1)

  28. GM5454443

    Disconnect and reposition harness as necessary.

  29. Loosen the fastener and slide the bracket out of the keyhole slot. (1)
  30. Serial Data Gateway Bracket (2) - Reposition
  31. GM5644434

    Remove the air distributor duct bolt (2) and reposition the instrument panel outer air outlet inner duct (1) as needed to gain access.

  32. Disconnect the electrical connector.
  33. GM5333075

    Retainer (1) - Release [2x]

  34. Brake Pedal Position Sensor Electrical Connector (2) - Disconnect
  35. GM5486242

    Brake Pedal Nut (1) - Remove [2x]

  36. Brake Master Cylinder Nut (2) - Remove [2x]
  37. GM5486241

    Depress the brake pedal retainer (1) locking tabs.

  38. Pull the brake pedal (2) outwards to release it from the brake pedal retainer (1).
  39. Remove and DISCARD the brake pedal retainer (1).
  40. GM5486242

    Brake Pedal Assembly (3) - Remove

scientia non olet · About LEMON Manuals