Removal Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.

Disable the SIR system. SIR Disabling and Enabling
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Lower Airbag Nut (1) - Remove [2x]
Instrument Panel Lower Airbag - Driver Side (2) - Remove
Disconnect the electrical connector.
Courtesy of GENERAL MOTORS COMPANY

With a flat bladed plastic trim tool, start at the front and work your way back to release the clips.
Instrument Panel Outer Trim Cover - Left Side (1) - Remove
Courtesy of GENERAL MOTORS COMPANY

Disconnect the hood primary latch release cable end retainer from the hood primary latch release cable handle (1).
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Lower Trim Panel Insulator Retainer (1) - Remove
Instrument Panel Insulator Bolt (2) - Remove [2x]
Instrument Panel Insulator Nut (3) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Use a plastic trim tool if necessary.

Release the tabs from the instrument panel lower trim panel insulator (1).
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Lower Trim Panel Insulator (1) - Remove
Disconnect the electrical connector.
Courtesy of GENERAL MOTORS COMPANY

Move the steering column up so you can access the lower left corner of the instrument panel center trim pad (1).
Start with a flat-bladed plastic trim tool in the lower left corner of the instrument panel center trim pad (1) and work your way clockwise.
Instrument Panel Center Trim Pad (1) - Remove
Disconnect the electrical connector.
Courtesy of GENERAL MOTORS COMPANY

Data Link Connector Bolt (1) - Remove [2x]
Instrument Panel Knee Bolster Bolt (2) - Remove [3x]
Courtesy of GENERAL MOTORS COMPANY

Release the clips with a suitable tool.
Disconnect and reposition harness as necessary.
Clear the instrument panel knee bolster deflector studs when removing the instrument panel knee bolster (1).
Courtesy of GENERAL MOTORS COMPANY

Pull the windshield garnish moldings (1) rearwards to release the tether from the A pillar.
Access the windshield garnish bolt (2) which is located on the backside of the windshield garnish moldings (1) and secures the tether to the A pillar.
Windshield Garnish Molding Bolt (2) - Remove [2x]
Disconnect the electrical connectors.
Windshield Garnish Molding (1) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

Using a flat-bladed plastic trim tool, release the retaining clips.
Instrument Panel Extension (1) - Remove
Disconnect the electrical connector.
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Instrument Cluster Hood (1) - Remove
Courtesy of GENERAL MOTORS COMPANY

Extend the steering column to its furthest point to allow the instrument panel steering column upper trim cover (1) to clear the instrument panel.
Using a small plastic trim tool, separate the instrument panel steering column upper trim cover (1) from the instrument panel steering column lower trim cover.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Instrument panel steering column upper trim cover is removed for graphic clarity.

{ If equipped } Disconnect the electrical connector. (1)
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Cluster Trim Plate Bolt (1) - Remove [2x]
Instrument Panel Cluster Trim Plate (2) - Remove
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Accessory Trim Plate Bolt @ Instrument Panel Carrier (1) - Remove [3x]
Instrument Panel Outer Upper Bolt (2) - Remove
Remove the instrument panel upper trim panel and instrument panel trim plate applique as an assembly (3).
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Outer Air Outlet Duct Retainer (1) - Remove
Instrument Panel Outer Air Outlet Duct - Left Side (2) - Remove