Removal Procedure
Refer to SIR Warning .
- Disable the SIR system. SIR Disabling and Enabling
With a flat bladed plastic trim tool, start at the front and work your way back to release the clips.
- Instrument Panel Outer Trim Cover - Left Side (1) - Remove
With a flat bladed plastic trim tool, start at the top to release the clip.
- Instrument Panel Radio Front Trim Plate (1) - Remove
With a flat bladed plastic trim tool, start at the top to release the clip.
- Instrument Panel Radio Front Trim Plate (1) - Remove
Radio Control Bolt (1) - Remove [2x]
- Disconnect the electrical connectors.
- Radio Control (2) - Remove
Instrument Panel Center Air Outlet Bolt (1) - Remove [3x]
- Instrument Panel Trim Plate (2) - Remove
Heater and Air Conditioning Control Bolt (1) - Remove [2x]
- Heater and Air Conditioning User Interface Control (2) - Remove
- Disconnect the electrical connector.
Hazard Warning Switch Bolt (1) - Remove [2x]
- Pull the hazard warning switch (2) straight back to release.
- Hazard Warning Switch (2) - Remove
- Disconnect the electrical connector.
Move the steering column up so you can access the lower left corner of the instrument panel center trim pad (1).
- Start with a flat-bladed plastic trim tool in the lower left corner of the instrument panel center trim pad (1) and work your way clockwise.
- Instrument Panel Center Trim Pad (1) - Remove
- Disconnect the electrical connector.
Front Floor Console (1) - Remove - Front Floor Console Removal and Installation (with M5N) , or Front Floor Console Removal and Installation (with MQA) , or Front Floor Console Removal and Installation (Blackwing)
Instrument Panel Lower Airbag Nut (1) - Remove [2x]
- Instrument Panel Lower Airbag - Driver Side (2) - Remove
- Disconnect the electrical connector.
Disconnect the hood primary latch release cable end retainer from the hood primary latch release cable handle (1).
Instrument Panel Lower Trim Panel Insulator Retainer (1) - Remove
- Instrument Panel Insulator Bolt (2) - Remove [2x]
- Instrument Panel Insulator Nut (3) - Remove [2x]
Instrument Panel Lower Trim Panel Insulator (1) - Remove
- Disconnect the electrical connector.
Data Link Connector Bolt (1) - Remove [2x]
- Instrument Panel Knee Bolster Bolt (2) - Remove [3x]
Pull instrument panel knee bolster (1) rear ward to disengage the clips, and lower past the instrument panel knee bolster deflector studs and remove.
- Disconnect and reposition harness as necessary.
Floor Front Air Outlet Duct Bolt (1) - Remove
- Floor Front Air Outlet Duct - Left Side- Outer (2) - Remove
Instrument Panel Tie Bar Brace Bolt (1) - Remove [3x]
- Instrument Panel Knee Bolster Deflector (2) - Remove
- NOTE:
Typical wiring harness shown. Individual wiring harnesses may differ based on option content.
Wiring Harness Clip (1) - Remove [2x]
- Reposition the wiring harness. (2)
- Heater and Air Conditioning Evaporator and Blower Upper and Blow Lower Case Bolt (3) - Remove
Floor Front Air Outlet Duct - Left Side- Inner (1) - Remove
With a flat bladed plastic trim tool, start at the front and work your way back to release the clips.
- Instrument Panel Outer Trim Cover - Right Side (1) - Remove
- { If equipped } Disconnect the electrical connector.
Body Control Module Bracket Bolt (1) - Remove
- Unlock and lower the body control module bracket (2) from the instrument panel lower trim panel insulator.
- NOTE:
Prior to disconnecting the BCM, one or both front windows should be down to allow access into the vehicle once the door is closed.
Release the detent (2) from the instrument panel lower trim panel insulator.
- Detach the wiring harness clips (1) from the body control module bracket.
- Disconnect the body control module connectors (3).
- Body Control Module (4) - Remove
Close and lock the body control module bracket (2) into the instrument panel lower trim panel insulator.
Instrument Panel Insulator Bolt (1) - Remove [4x]
- NOTE:
Use a plastic trim tool if necessary.
Release the front edge of the front console extension panel from the instrument panel lower trim panel insulator (1).
- Instrument Panel Lower Trim Panel Insulator (1) - Remove
- Disconnect the electrical connectors.
Instrument Panel Lower Airbag Nut (1) - Remove [2x]
- Instrument Panel Lower Airbag - Passenger Side (2) - Remove
- Disconnect the electrical connector.
Instrument Panel Compartment Bolt (1) - Remove [5x]
Instrument Panel Compartment (1) - Remove
- Disconnect the electrical connectors.
Using a flat-bladed plastic trim tool, release the retaining clips.
- Instrument Panel Trim Pad (1) - Remove
Instrument Panel Center Trim Panel Bolt (1) - Remove [6x]
Instrument Panel Lower Center Trim Panel (1) - Remove
- Disconnect the electrical connector.
Instrument Panel Center Air Outlet Duct Retainer (1) - Remove [2x]
- Instrument Panel Compartment Air Duct- Outer (2) - Remove
Instrument Panel Center Air Outlet Duct Retainer (1) - Remove
Instrument Panel Compartment Air Duct- Inner (1) - Remove
- Maneuver the instrument panel compartment air duct - inner (1) out from behind the Instrument panel.