Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT5. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of GENERAL MOTORS COMPANY

Using an assistant to reposition the brake master cylinder - with power brake booster and electronic brake control module, install the brake pedal assembly (3).

CAUTION:

Refer to Fastener Caution .

Brake Master Cylinder Nut (2) - Install and tighten [2x] - Brake Master Cylinder Replacement - With Power Brake Booster and Electronic Brake Control Module (without MJK)
Brake Pedal Nut (1) - Install and tighten [2x] 25 N.m (18 lb ft)
Courtesy of GENERAL MOTORS COMPANY

Engage the brake pedal (1) to the brake master cylinder push rod by pushing inwards.
Ensure the brake pedal retainer is secured by lightly pulling rearward on the brake pedal (1).
Courtesy of GENERAL MOTORS COMPANY

Brake Pedal Position Sensor Electrical Connector (2) - Connect
Retainer (1) - Secure [2x]
Courtesy of GENERAL MOTORS COMPANY

Reposition the instrument panel outer air outlet inner duct (1).
Air Distributor Duct Bolt (2) - Install and tighten - Instrument Panel Outer Air Outlet Inner Duct Replacement - Left Side
Courtesy of GENERAL MOTORS COMPANY

Serial Data Gateway Bracket (2) - Install
Serial Data Gateway Module Bracket Bolt (1) - Tighten [2x] - Serial Data Gateway Bracket Replacement
Connect and position the wiring harness.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Typical wiring harness shown. Individual wiring harnesses may differ based on option content.

Connect the electrical connectors. (1)
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Knee Bolster Deflector (2) - Install
Instrument Panel Tie Bar Brace Bolt (1) - Install and tighten [3x] - Instrument Panel Knee Bolster Deflector Replacement
Courtesy of GENERAL MOTORS COMPANY

Floor Front Air Outlet Duct - Left Side Outer (2) - Install
Floor Front Air Outlet Duct Bolt (1) - Install and tighten - Floor Front Air Outlet Duct Replacement - Left Side Outer
Courtesy of GENERAL MOTORS COMPANY

Connect and position the wiring harness.
Instrument Panel Knee Bolster (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Data Link Connector Bolt (1) - Install and tighten [2x] - Instrument Panel Knee Bolster Replacement
Instrument Panel Knee Bolster Bolt (2) - Install and tighten [3x] - Instrument Panel Knee Bolster Replacement
Connect the electrical connector.
Courtesy of GENERAL MOTORS COMPANY

Connect the electrical connector.
Instrument Panel Center Trim Pad (1) - Install
Return the steering column to its original position.
Courtesy of GENERAL MOTORS COMPANY

Connect the electrical connector.
Instrument Panel Lower Trim Panel Insulator (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Install the tabs into the instrument panel lower trim panel insulator (1).
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Lower Trim Panel Insulator Retainer (1) - Install
Instrument Panel Insulator Bolt (2) - Install and tighten [2x] - Instrument Panel Lower Trim Panel Insulator Replacement - Left Side
Instrument Panel Insulator Nut (3) - Install and tighten [2x] - Instrument Panel Lower Trim Panel Insulator Replacement - Left Side
Courtesy of GENERAL MOTORS COMPANY

Attach the hood primary latch release cable end retainer to the hood primary latch release cable handle (1).
Courtesy of GENERAL MOTORS COMPANY

Instrument Panel Outer Trim Cover - Left Side (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Connect the electrical connector.
Instrument Panel Lower Airbag - Driver Side (2) - Install
Instrument Panel Lower Airbag Nut (1) - Install and tighten [2x] - Instrument Panel Lower Airbag Replacement - Driver Side
Enable the SIR System. SIR Disabling and Enabling .
Calibrate the brake pedal position sensor. Brake Pedal Position Sensor Calibration