Fastener Specifications
WARNING: This page is about a different car, the 2022 Cadillac CT5. However, it is still accessible from the selected car via links, so may be relevant.
Single Use Non-Threaded Fasteners/Components
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| 1st and 2nd Gear Synchronizer Retaining Ring |
| 1st and 2nd Shift Fork Pin |
| 3rd and 4th Gear Synchronizer Retaining Ring |
| 5th and 6th Gear Synchronizer Hub Retaining Ring |
| 5th Gear Retaining Ring |
| 5th Gear Thrust Washer |
| Clutch Housing Gasket |
| Counter Drive Gear Retaining Ring |
| Counter Gear Rear Bearing Retaining Ring |
| Input Shaft Seal |
| Main Shaft Bearing Retaining Ring |
| Main Shaft Rear Bearing Retaining Ring |
| Main Shaft Rear Seal |
| Manual Transmission Gear Position Sensor Seal |
| Manual Transmission Reverse Gear Blockout Solenoid Housing Seal |
| Propeller Shaft Transmission Yoke Washer |
| Reverse Gear Retaining Ring |
| Reverse Gear Synchronizer Retainer |
| Reverse Shift Block Interlock Pin |
| Reverse Shift Fork Retaining Ring |
| Selector Lever Pivot Pin |
| Shift Control Lever Shaft Pin |
| Shift Control Shaft Cover Seal |
| Shift Lever Retaining Ring |
| Shift Shaft Detent Plug |
| Shift Shaft Interlock Pin |
| Transmission Adapter Plug |
| Transmission Case Plug |
| Transmission Extension Gasket |
| Transmission Extension Nut |
| Transmission Fluid Cooler Inlet Pipe Fitting |
| Transmission Fluid Pump Inlet Pipe Seal |
| Transmission Fluid Pump Outlet Pipe Fitting |
| Transmission Fluid Pump Retaining Ring |
| Vehicle Speed Sensor Seal |
Single Use Threaded Fastener/Component Tightening Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Automatic Transmission Manual Shift Auxiliary Position Switch Bolt | 20 N.m (15 lb ft) |
| Clutch Housing Adapter Bolt | 34 N.m (25 lb ft) |
| Manual Transmission Gear Position Sensor Bolt | 9 N.m (80 lb in) |
| Manual Transmission Output Speed Sensor Bolt | 11 N.m (97 lb in) |
| Manual Transmission Reverse Gear Blockout Solenoid Housing Bolt | 18 N.m (13 lb ft) |
| Propeller Shaft Transmission Yoke Nut | 136 N.m (100 lb ft) |
| Reverse Idler Gear Shaft Bracket Bolt | 25 N.m (18 lb ft) |
| Shift Control Shaft Cover Bolt | 20 N.m (15 lb ft) |
| Shift Guide Detent Plate Bolt | 22 N.m (16 lb ft) |
| Shift Shaft Detent Lever Bolt | 40 N.m (30 lb ft) |
| Shift Shaft Detent Plug | 24 N.m (18 lb ft) |
| Transmission Adapter Plug | 34 N.m (25 lb ft) |
| Transmission Extension Bolt | 48 N.m (35 lb ft) |
| Transmission Extension Nut | 48 N.m (35 lb ft) |
| Transmission Extension Stud | 48 N.m (35 lb ft) |
| Transmission Fluid Auxiliary Cooler Bracket Nut | 20 N.m (15 lb ft) |
| Transmission Fluid Cooler Outlet Pipe Fitting | 22 N.m (16 lb ft) |
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Manual Transmission Control Lever Knob Bolt | 7 N.m (62 lb in) |
| Manual Transmission Gear Position Sensor | 10 N.m (89 lb in) |
| Manual Transmission Fluid Temperature Sensor | 39 N.m (29 lb ft) |
| Manual Transmission Reverse Gear Blockout Solenoid | 18 N.m (13 lb ft) |
| Shift Interlock Detent | 40 N.m (30 lb ft) |
| Transmission Bolt@Engine Block | 68 N.m (50 lb ft) |
| Transmission Bolt@Oil Pan | 30 N.m (22 lb ft) |
| Transmission Oil Filler Plug | 27 N.m (20 lb ft) |
| Transmission Oil Drain Plug | 27 N.m (20 lb ft) |
| Transmission Mount Bolt@Transmission Crossmember | 61 N.m (45 lb ft) |
| Transmission Mount Bolt | 41 N.m (30 lb ft) |
| Transmission Stud | 41 N.m (30 lb ft) |