LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 25 (Steering Wheel And Column) >> Repair Instructions >> Steering Wheel Spoke Cover Replacement (Blackwing with MHU) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5874911Courtesy of GENERAL MOTORS COMPANY

    Cruise Control Switch (4) - Install

    2. CAUTION:

    Fastener Caution .

  2. Steering Wheel Bolt (2) @ Cruise Control Switch (4) - Install and tighten [3x] - Fastener Specifications
  3. Radio Control Switch (3) - Install
  4. Steering Wheel Bolt (1) @ Radio Control Switch (3) - Install and tighten [3x] - Fastener Specifications
  5. GM5874909Courtesy of GENERAL MOTORS COMPANY

    Ride Control Switch (4) - Install

  6. Steering Wheel Bolt (2) @ Ride Control Switch (4) - Install and tighten [2x] - Fastener Specifications
  7. Drive Mode Selector Auxiliary Switch (3) - Install
  8. Steering Wheel Bolt (1) @ Drive Mode Selector Auxiliary Switch (3) - Install and tighten [2x] - Fastener Specifications
  9. GM5336583Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel Trim Spoke Cover Applique (1) - Install

  10. Connect the electrical connectors.
  11. GM5336584Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel Bolt (1) @ Steering Wheel Spoke Cover - Install and tighten [2x] - Fastener Specifications 

  12. GM5428745Courtesy of GENERAL MOTORS COMPANY

    Automatic Transmission Manual Shift Auxiliary Position Switch-Left Side (1) - Install

  13. Connect the electrical connector.
  14. GM5428772Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connector.

  15. Automatic Transmission Manual Shift Auxiliary Position Switch-Right Side (1) - Install
  16. GM5868318Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel Shroud (1) - Install

  17. Connect the electrical connectors.
  18. GM5868312Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel Bolt (2) @ Steering Wheel Shroud - Install and tighten [6x] - Fastener Specifications 

  19. Steering Wheel Bolt (1) @ Automatic Transmission Manual Shift Auxiliary Position Switch - Install and tighten [4x] - Fastener Specifications
  20. GM5421652Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel (2) - Install

  21. If a NEW threaded component is being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded component is reused, prepare the threaded component using the following steps:
    1. Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
    2. Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Remove loose debris from internal and external threads using compressed air.
    4. Apply liquid thread locking adhesive in a strip along half of the length of the external threads, starting at the tip, just prior to installation. Adhesives, Fluids, Lubricants, and Sealers 
  22. Steering Wheel Bolt (1) - Install and tighten - Fastener Specifications 
  23. GM5443287Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connectors.

  24. Install any connector position assurance (CPA) devices or secondary locks.
  25. Steering Wheel Airbag (2) - Install
  26. Steering Wheel Airbag Bolt (1) - Install and tighten [2x] - Fastener Specifications
  27. GM5421708Courtesy of GENERAL MOTORS COMPANY

    Install the 2 steering wheel airbag access hole covers (1).

  28. Enable the SIR System. SIR Disabling and Enabling
scientia non olet · About LEMON Manuals