LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 220 (Engine Mechanical - 2.0L (LSY) - Repair Instructions (1 Of 3)) >> Repair Instructions >> Timing Chain Guide Replacement (Non Tensioner Side) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. Clean the threaded timing chain tensioner bolt holes.
  2. Clean all sealing surfaces.
  3. GM5442548

    Timing Chain Tensioner (1) - Install

  4. Timing Chain Tensioner Bolt (2) - Install [2x] - Fastener Specifications
  5. GM5135546

    Timing Chain Guide (2) - Install

  6. Timing Chain Guide Bolt (1) - Install and hand tighten [2x]
  7. GM5431937

    Timing Chain (1) - Reposition

  8. GM5164972
    CAUTION:

    Hold the camshaft sprocket firmly and squarely during camshaft sprocket bolt removal/installation. Failure to do so may result in damage to the inside of the camshaft sprocket.

    Hold the intake camshaft sprocket (1) with hands from underneath the EN-52461  Cam Phaser Torque Reaction Tool (3) and install the EN-52461 - 1  Holder (3) into the intake camshaft sprocket to hold it securely before installing the camshaft sprocket bolt.

  9. Line up intake camshaft sprocket (1) with alignment marks, as you install them on chain and the housing which should of been done on removal.
  10. GM5164974

    Hold the exhaust camshaft sprocket (1) with hands from underneath the EN-52461  Cam Phaser Torque Reaction Tool (3) and install the EN-52461 - 1  Holder (3) into the exhaust camshaft sprocket to hold it securely before installing the camshaft sprocket bolt (1).

  11. Line up exhaust camshaft sprocket (1) with alignment marks, as you install them on chain and the housing which should of been done on removal.
  12. GM5285327

    Lubricate the camshaft sprocket bolts (1) with clean engine oil where indicated. Adhesives, Fluids, Lubricants, and Sealers

  13. GM5150021

    Camshaft Sprocket Bolt (1) - Install NEW and hand tighten

  14. GM5002079

    Check that the EN-52461 - 1  Holder (1) sits correctly in the hole of the camshaft sprocket.

  15. Rotate the EN-52461 - 1  Holder counter clockwise (1).
  16. While holding the EN-52461 - 1  Holder (1) in the clockwise position to 6 N.m (53 lb in), tighten the bolt (4) just enough to hold the EN-52461 - 1  Holder in place.
    17. CAUTION:

    Refer to Torque-to-Yield Fastener Caution .

  17. Intake Camshaft Sprocket Bolt (2) - Tighten - Fastener Specifications
  18. Check that the EN-52461 - 1  Holder (1) sits correctly in the hole of the exhaust camshaft sprocket.
  19. Rotate the EN-52461 - 1  Holder counter clockwise.
  20. While holding the EN-52461 - 1  Holder in the counter clockwise position 6 N.m (53 lb in), tighten the bolt (3) just enough to hold the EN-52461 - 1  Holder in place.
  21. Exhaust Camshaft Sprocket Bolt (2) - Tighten - Fastener Specifications
  22. GM5135546

    Timing Chain Guide Bolt (1) - Tighten [2x] - Fastener Specifications

  23. GM5002102

    Bolt (1, 2) - Loosen

  24. Slide the 2 EN-52461 - 1  Holder (3) out of the camshaft sprockets.
  25. GM5002065

    Loosen the 2 bolts (1, 4) of EN-52461 - 100  Adapter Cam Phaser Torque Reaction Tool (5).

  26. Remove the EN-52461  Cam Phaser Torque Reaction Tool (5) along with the 2 EN-52461 - 100  Adapter Cam Phaser Torque Reaction Tool (2, 3) from the engine.
  27. GM5149274

    Remove the EN-52462 - A  Camshaft Tool (1) by rotating the levers in direction of arrows.

  28. GM5285281

    Loosen and disengage the bolt (2) from EN-52462-A  Camshaft Alignment Tool (1).

  29. EN-52462-A  Camshaft Alignment Tool (1) - Remove
  30. GM5525924

    Clean and apply sealant to the camshaft cover opening plugs (1). Adhesives, Fluids, Lubricants, and Sealers

  31. Camshaft Cover Opening Plug (1) - Install and tighten [2x] - Fastener Specifications
  32. GM5285267

    Engine Wiring Harness (2) @ Camshaft Carrier - Install

  33. Retainer (1) - Install [3x]
  34. GM4997073
    NOTE:
    • The timing chain upper cover sealing surface must be free of contamination prior to applying the sealer.
    • Install and align the timing chain upper cover to engine block within 10 minutes of applying the sealer.
    • The timing chain upper cover must be fastened to final torque specification within 15 minutes of applying the sealer.
    • Ensure proper use of room temperature vulcanizing (RTV) sealant. Use of Room Temperature Vulcanizing (RTV) and Anaerobic Sealant

    Apply approximately a 5 mm (0.2 in) thick bead of sealant (2) on both sides between the camshaft housing and the cylinder head. Adhesives, Fluids, Lubricants, and Sealers .

  35. Check that the 2 Pins (1) are in the camshaft housing or in the timing chain upper cover.
  36. GM4997066

    Timing Belt Front Upper Cover Seal (1) - Install NEW

  37. Timing Chain Upper Cover (2) - Install
  38. GM4997059

    Timing Chain Upper Cover BoltM6 (3) - Install and tighten in sequence - Fastener Specifications

  39. Timing Chain Upper Cover Bolt M5 (2) - Install and tighten in sequence [11x] - Fastener Specifications
  40. GM5439441

    Camshaft Position Actuator Magnet Gasket (3) - Install NEW

  41. Camshaft Position Actuator Valve Solenoid (2) - Install
  42. Camshaft Position Actuator Valve Solenoid Bolt (1) - Install [2x] - Fastener Specifications
  43. GM5439440

    Camshaft Position Actuator Magnet Gasket (3) - Install NEW

  44. Camshaft Position Actuator Valve Solenoid (2) - Install
  45. Camshaft Position Actuator Valve Solenoid Bolt (1) - Install [2x] - Fastener Specifications
  46. GM5562846

    Engine Wiring Harness (3) - Reposition

  47. Retainer (1) @ Timing Chain Upper Cover (2) - Engage [6x]
  48. Connect the 2 electrical connectors to the camshaft position actuator valve solenoids.
  49. GM5442955

    EN-955-10A  Locking Pin (1) - Remove

  50. GM4998009
    NOTE:
    • The engine front cover sealing surface must be free of contamination prior to applying the sealer.
    • Install and align the engine front cover to engine block within 10 minutes of applying the sealer.
    • The engine front lower cover must be fastened to final torque specification within 15 minutes of applying the sealer.
    • Ensure proper use of room temperature vulcanizing (RTV) sealant. Use of Room Temperature Vulcanizing (RTV) and Anaerobic Sealant

    Apply approximately a 4 mm (0.16 in) thick bead of sealant (1) to the engine front cover. Adhesives, Fluids, Lubricants, and Sealers

  51. Crankshaft Balancer Bolt - Remove and DISCARD
  52. GM5108952

    Install EN-52440  Crankshaft Oil Seal Ring Guide Front (2) to the crankshaft.

  53. Install the engine front cover (1) backwards using the 2 tabs to size the seal.
  54. GM4998004

    Remove the engine front cover (1) after seal is sized.

  55. EN-52483  Guide Pins (2) - Install
  56. Engine Front Cover (1) - Install
  57. Remove the EN-52440  Crankshaft Oil Seal Ring Guide Front (3).
  58. GM4997994

    Remove the EN-52483  Guide Pins (2).

  59. Engine Front Cover Bolt (1) - Install and hand tighten [9x]
  60. Engine Front Cover Bolt (1) - Tighten in sequence [9x] - Fastener Specifications
  61. Raise and support the vehicle. Lifting and Jacking the Vehicle
  62. GM5164169
    NOTE:

    The timing pin (3) is installed into the flexplate for engine timing procedures, it can be damaged if torque is applied to the flexplate with the timing pin engaged. The timing pin must be placed in the retracted position using the handle (1) and twisting to locked position. The slide part (4) to be installed to the flex plate when torque is applied to the flexplate or crankshaft balancer bolt.

    Retract the timing pin (3) using the handle (1) of the EN-52476  Flywheel Lock and Alignment Tool (2).

  63. Ensure to engage the slide (4) of the EN-52476  Flywheel Lock and Alignment Tool (2) into the automatic transmission flexplate.
  64. Lower the vehicle.
  65. GM4998850

    Crankshaft Balancer (2) - Install

  66. Crankshaft Balancer Bolt (1) - Install NEW and tighten - Fastener Specifications
  67. GM5129786

    Accessory Drive Primary Belt (1) - Install

  68. GM5129599

    Use a suitable tool to rotate the drive belt tensioner (1) counterclockwise and hold.

  69. Slowly release tension on the drive belt tensioner.
  70. Raise and support the vehicle. Lifting and Jacking the Vehicle
  71. GM5164169
    NOTE:

    The timing pin (3) is installed into the flexplate for engine timing procedures, it can be damaged if torque is applied to the flexplate with the timing pin engaged. The timing pin must be placed in the retracted position using the handle (1) and twisting to locked position. The slide part (4) to be installed to the flex plate when torque is applied to the flexplate or crankshaft balancer bolt.

    EN-52476  Flywheel Lock and Alignment Tool (2) - Remove

  72. GM5319715

    Starter (3) - Install

  73. Starter Bolt (2) - Install and tighten [2x] - Fastener Specifications
  74. Starter Stud (1) - Install and tighten - Fastener Specifications
  75. GM5460947

    Auxiliary Generator Battery Jumper Cable (2) - Install

  76. Battery Positive Cable Nut (1) @ Starter Solenoid - Install and tighten - Fastener Specifications
  77. GM5460935

    Electrical Connector (1) - Connect

  78. GM5460874

    Auxiliary Generator Battery Jumper Cable (3) - Install

  79. Battery Negative Cable Nut (1) @ Starter Stud - Install and tighten - Fastener Specifications
  80. Engine Wiring Harness Retainer (2) - Engage [2x]
  81. Lower the vehicle.
  82. GM5068106

    Oil Level Indicator Tube Seal (2) - Install NEW

  83. Oil Level Indicator Tube (1) - Install
  84. GM5136547

    Oil Level Indicator Tube Bracket Bolt (2) - Install and tighten - Fastener Specifications

  85. Electrical Connector (1) @ Oil Level Indicator Tube (3) - Clip
  86. GM5335764
  87. Oil Level Indicator (1) - Install
  88. GM5080707

    Evaporative Emission Canister Purge Tube (2) - Install

  89. Connect the quick disconnects (1) and install the retainer (3). Plastic Collar Quick Connect Fitting Service
  90. GM5335089

    Intake Manifold Cover (1) @ Upper Intake Manifold Bracket (2) - Install

  91. GM5335087
    NOTE:

    Ensure the engine sight shield retainers fully engage the intake manifold cover studs.

    Push down on the front of the intake manifold cover (1) as indicated by the arrow.

  92. Fill the engine oil to the proper level with NEW engine oil. Engine Oil and Oil Filter Replacement (RWD) , or Engine Oil and Oil Filter Replacement (AWD)
  93. Install the oil fill cap.
  94. Connect the battery. Battery Negative Cable Disconnection and Connection
  95. Perform the engine oil life reset. GM Oil Life System Resetting (With Scan Tool) , or GM Oil Life System Resetting (Without Scan Tool)
  96. Check for leaks.
scientia non olet · About LEMON Manuals