LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 158 (Engine Mechanical - 2.7L (L3B) - Repair Instructions (1 Of 3)) >> Repair Instructions >> Balancer Chain Guide Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5153495

    Balancer Chain Guide (3) - Install

    2. CAUTION:

    Refer to Fastener Caution .

  2. Timing Chain Guide Bolt (2) - Install and tighten [2x] - Fastener Specifications
  3. GM5153596

    EN-52593  Chain Tensioner Retention Pin (2) - Remove

  4. GM5021095

    EN-52483  Cover Installation Guide Pins - Install

  5. GM5045205
    NOTE:

    Ensure that the sealing surface is clear of oil, grease and old sealant material.

    NOTE:

    Ensure proper use of room temperature vulcanizing (RTV) sealant. Use of Room Temperature Vulcanizing (RTV) and Anaerobic Sealant

    NOTE:

    The rear oil seal housing must be installed within 8 minutes of applying the RTV sealant application.

    Apply a bead of room temperature vulcanizing sealant (1) as shown. Adhesives, Fluids, Lubricants, and Sealers

  6. GM5021095
    NOTE:

    Leave the seal protector that ships installed onto the NEW crankshaft rear oil seal housing on.

    Install the NEW rear crankshaft rear oil seal housing (2) until the seal protector is flush with the end of the crankshaft.

  7. Press the center of the crankshaft NEW rear oil seal housing in, allowing the crankshaft to push out the seal protector.
  8. DISCARD the seal protector.
  9. Once the NEW rear oil seal housing is completely seated, inspect the seal around the crankshaft to ensure it has not folded over itself.
  10. EN-52483  Cover Installation Guide Pins - Remove
  11. GM5004098

    Crankshaft Rear Oil Seal Housing Bolt (1) - Install and hand tighten [14x]

  12. Crankshaft Rear Oil Seal Housing Bolt (1) - Tighten in sequence [14x] - Fastener Specifications
  13. GM5511922

    Crankshaft Position Sensor (2) - Install

  14. Crankshaft Position Sensor Bracket Bolt (1) - Install and tighten - Fastener Specifications
  15. GM5511921

    Electrical Connector (1) - Connect

  16. GM5140979

    Flywheel Locating Pin (2) - Install

  17. Crankshaft Position Sensor Reluctor Ring (1) - Install
  18. GM5517309

    Automatic Transmission Flex Plate (2) - Install

    19. NOTE:

    Install NEW bolts. Do NOT reuse old bolts.

  19. If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:
    1. Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
    2. Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Apply thread locking adhesive to the external threads of the component. Adhesives, Fluids, Lubricants, and Sealers
    4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
  20. Automatic Transmission Flex Plate Bolt (1) - Install NEW and hand tighten [8x] - Fastener Specifications
  21. GM5150614

    Remove the EN-52476  Flywheel Lock and Alignment Tool

  22. Install the transmission. Transmission Replacement (All Wheel Drive) , or Transmission Replacement (Rear Wheel Drive)
scientia non olet · About LEMON Manuals