Installation Procedure
- Clean all sealing surfaces.
Slip the EN-52439 - 3 Crankshaft Oil Seal Ring Guide Rear (2) through the seal from the outside cover to inside 2 times to shape the seal lip in the crankshaft rear oil seal housing (1).
Install the EN-52439 - 3 Crankshaft Oil Seal Ring Guide Rear (2) through the seal with the EN-52439 - 1 Crankshaft Oil Seal Ring Guide Rear (1) to keep the shape of the seal in the crankshaft rear oil seal housing (3).
- NOTE:
- The crankshaft rear oil seal housing surface must be free of contamination prior to applying the sealer.
- Install and align the crankshaft rear oil seal housing to the block within 10 minutes after applying the sealer.
- The crankshaft rear oil seal housing must be fastened to final torque specification within 15 minutes after applying the sealer.
Set the crankshaft rear oil seal housing on the EN-52439 - 1 Crankshaft Oil Seal Ring Guide Rear (2) and apply approximately a 4 mm (0.16 in) thick bead of sealant 1) to the crankshaft rear oil seal housing. Adhesives, Fluids, Lubricants, and Sealers
EN-52483 Guide Pins (2) - Install
- Crankshaft Rear Oil Seal Housing (1) - Install NEW
- EN-52439 - 1 Crankshaft Oil Seal Ring Guide Rear (3) - Remove
Crankshaft Rear Oil Seal Housing Bolt (1) - Install and hand tighten [11x]
- EN-52483 Guide Pins - Remove
- Crankshaft Rear Oil Seal Housing Bolt (1) - Install and hand tighten [2x]
- Crankshaft Rear Oil Seal Housing Bolt (1) - Tighten in sequence [13x] - Fastener Specifications
- CAUTION:
Do not allow the crankshaft position sensor reluctor ring to come into contact with external magnetic fields or sharp metal objects. Do not drop the crankshaft position sensor reluctor ring. Do not damage the rubberized encoder track. Failure to follow these precautions may cause damage to the component.
NOTE:Ensure that the flywheel locating pin (2) sits in the correct holes in the crankshaft and the crankshaft position sensor inner exciter ring.
Flywheel Locating Pin (2) - Install
- Crankshaft Position Sensor Inner Exciter Ring (1) - Install
Crankshaft Position Sensor (2) - Install
- Crankshaft Position Sensor Bolt (1) - Install and tighten - Fastener Specifications
- Clean the 8 flex plate bolt hole threads in the crankshaft.
- If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:
- Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
- Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
- Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
- Ensure there are no gaps in the thread locking adhesive once applied to the component.
Automatic Transmission Flex Plate (1) - Install
- Check that guide pin (2) is in the correct hole of the automatic transmission flex plate.
- Automatic Transmission Flex Plate Bolt (3) - Install, but do NOT tighten [8x]
EN-52476 Flywheel Holding Tool (1) - Install
- Automatic Transmission Flex Plate Bolt (2) - Tighten in sequence [8x] - Fastener Specifications
- EN-52476 Flywheel Holding Tool (1) - Remove
- Transmission - Install - Transmission Replacement (Rear Wheel Drive) , or Transmission Replacement (All Wheel Drive)
This vehicle is equipped with torque-to-yield or single use fasteners. Install a NEW torque-to-yield or single use fastener when installing this component. Failure to replace the torque-to-yield or single use fastener could cause damage to the vehicle or component.