Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.

Engine Coolant Air Bleed Pipe (1) - Install
Install the transmission vent hose retainer to the engine coolant air bleed pipe.
Engine Coolant Air Bleed Pipe (2) @ Auxiliary Water Pump Inlet Pipe - Install
Hose Clamp (1) - Engage - Hose Clamp Replacement Guidelines - Spring Type
Raise the vehicle.
Automatic Transmission Fluid Cooling Exchanger (2) - Install

CAUTION:

Refer to Fastener Caution .

Transmission Fluid Auxiliary Cooler Bracket Nut (1) - Install and tighten - Fastener Specifications
Transmission Fluid Auxiliary Cooler Bolt (1) - Install and tighten [2x] - Fastener Specifications
Transmission Fluid Cooler Pipe Seal (1) - Install NEW [2x]
NOTE:
Remove the caps from the fittings and plugs from the holes before installing the transmission fluid cooler pipes.

Transmission Fluid Cooler Inlet and Outlet Pipe (2) @ Automatic Transmission Fluid Cooling Exchanger - Install [2x]
Transmission Fluid Cooler Pipe Nut (1) - Install and tighten [2x] - Fastener Specifications
Automatic Transmission Fluid Cooling Heat Exchanger Outlet Hose (2) @ Automatic Transmission Fluid Cooling Exchanger - Install
Automatic Transmission Fluid Cooling Heat Exchanger Outlet Hose Clamp (1) @ Automatic Transmission Fluid Cooling Exchanger - Engage - Hose Clamp Replacement Guidelines - Spring Type
Automatic Transmission Fluid Cooling Heat Exchanger Inlet Hose (1) @ Automatic Transmission Fluid Cooling Exchanger - Install
Automatic Transmission Fluid Cooling Heat Exchanger Inlet Hose Clamp (1) @ Automatic Transmission Fluid Cooling Exchanger - Engage - Hose Clamp Replacement Guidelines - Spring Type
Lower the vehicle.
Engine Coolant Air Bleed Pipe (2) @ Engine Coolant Air Bleed Hose - Install
Hose Clamp (1) - Engage - Hose Clamp Replacement Guidelines - Spring Type
Engine Coolant Air Bleed Pipe Bolt (1) - Install and tighten [2x] - Fastener Specifications
Engine Wiring Harness Bracket (3) - Install
Engine Wiring Harness Conduit Nut (2) - Install and tighten - Fastener Specifications
Engine Wiring Harness Conduit Bracket Bolt (1) - Install and tighten - Fastener Specifications
Engine Wiring Harness (2) - Reposition
Retainer (1) - Install [5x]
Heater Inlet Hose (2) @ Engine Coolant Thermostat Housing Pipe - Install
Heater Inlet Hose Retainer (1) - Engage
Radiator Surge Tank Inlet Hose (2) @ Engine Coolant Thermostat Housing Pipe - Install
Hose Clamp (1) - Engage - Hose Clamp Replacement Guidelines - Spring Type
Intake Manifold Cover (1) - Install
Position the intake manifold cover (1) in place..
Install the oil fill cap.
Plenum Front Panel (1) - Install
Plenum Front Panel Bolt (1) - Install and tighten [4x] - Fastener Specifications
Plenum Front Panel Nut (2) - Install and tighten [3x] - Fastener Specifications
{If equipped} Install the forward lamp wiring harness extension (3) into the plenum front panel.
Plenum Front Panel Nut (1) - Install and tighten [3x] - Fastener Specifications
Plenum Front Panel Bolt (2) - Install and tighten [3x] - Fastener Specifications
Install the forward lamp wiring harness extension (3) into the plenum front panel.
Install the forward lamp wiring harness extension retainers as necessary.
Air Inlet Deflector Water Deflector (1) - Install
Air Inlet Deflector Water Deflector Retainer (1) - Install [2x]
Install the windshield wiper system module (2) in the vehicle.
Windshield Wiper System Module Bolt (1) - Install and tighten [2x] - Fastener Specifications
Connect the windshield wiper motor electrical connector.
Connect the battery negative cable. Battery Negative Cable Disconnection and Connection
Windshield Wiper System Module Shield (1) - Install
Air Inlet Grille Panel (2) - Install
1. Install the air inlet grille panel (2) between both hood hinges.
2. Connect the windshield washer nozzle hose to the windshield washer pump hose.
3. Air Inlet Grille Panel Retainer (1) - Install [6x]
Install the front compartment side sight shield (2) to the left and right side.
Install the 2 front compartment side sight shield retainer (1) to the left and right side.
Install the hood rear outer air inlet seal (2) to the left and right side.
Install the 2 hood rear outer air inlet seal retainer (1) to the left and right side.
Air Inlet Grille Panel Extension (1) - Install [2x]
1. Install the air inlet grille panel extension (1).
2. Remove the masking tape from the top edge of the service part.
3. Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.
Windshield Wiper Arm (3) - Install [2x]
1. Clean the windshield wiper transmission pivot shaft splines with a soft wire brush before installing the windshield wiper arm (3).
2. Position the windshield wiper arm (3) on the windshield wiper transmission pivot shaft.
3. Windshield Wiper Arm Nut (2) - Install and tighten Fastener Specifications
4. Windshield Wiper Arm Finish Cap (1) - Install
If required, realign the windshield wipers to their respective alignment circles (1) on the windshield.
1. Lubricate the windshield with clean washer fluid.
2. Run the windshield wipers for two complete cycles then turn off the windshield wipers.
3. Ensure the windshield wipers are in the full park position.
4. Inspect the windshield wipers for proper position to the alignment circles (1) on the windshield.
Fill the cooling system to the proper level. Cooling System Draining and Filling (LSY GE 47716) , or Cooling System Draining and Filling (LSY Static Fill) , or Cooling System Draining and Filling (LSY with V03 Static Fill) , or Cooling System Draining and Filling (LSY with V03 GE 47716)
Start the engine and check for coolant leaks.