LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 134 (Engine Heating And Cooling - Repair Instructions (2 Of 2)) >> Repair Instructions >> Engine Coolant Air Bleed Hose Replacement (Engine Coolant Flow Control Vale to Engine Coolant Heater Exhaust PIpe) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5323387

    Engine Coolant Air Bleed Hose (2) - Install

  2. Hose Clamp (1) - Engage [2x] - Hose Clamp Replacement Guidelines - Spring Type
  3. GM5323709

    Transmission Vent Hose Retainer (1) @ Engine Coolant Air Bleed Hose - Install

  4. GM5422044

    Plenum Front Panel (1) - Install

  5. GM5422041

    Plenum Front Panel Bolt (1) - Install and tighten [4x] - Fastener Specifications

  6. Plenum Front Panel Nut (2) - Install and tighten [3x] - Fastener Specifications
  7. Install the forward lamp wiring harness extension (3) into the plenum front panel.
  8. GM5422039

    Plenum Front Panel Nut (1) - Install and tighten [3x] - Fastener Specifications

  9. Plenum Front Panel Bolt (2) - Install and tighten [3x] - Fastener Specifications
  10. Install the forward lamp wiring harness extension (3) into the plenum front panel.
  11. Install the forward lamp wiring harness extension retainers as necessary.
  12. GM5499583

    Air Inlet Deflector Water Deflector (1) - Install

  13. GM5499581

    Air Inlet Deflector Water Deflector Retainer (1) - Install [2x]

  14. GM5420344

    Install the windshield wiper system module (2) in the vehicle.

  15. Windshield Wiper System Module Bolt (1) - Install and tighten [2x] - Fastener Specifications
  16. Connect the windshield wiper motor electrical connector.
  17. Connect the battery negative cable. Battery Negative Cable Disconnection and Connection
  18. GM5420286

    Windshield Wiper System Module Shield (1) - Install

  19. GM5417442

    Air Inlet Grille Panel (2) - Install

    1. Install the air inlet grille panel (2) between both hood hinges.
    2. Connect the windshield washer nozzle hose to the windshield washer pump hose.
    3. Air Inlet Grille Panel Retainer (1) - Install [6x]
  20. GM5421990

    Install the front compartment side sight shield (2) to the left and right side.

  21. Install the 2 front compartment side sight shield retainers (1) to the left and right side.
  22. GM5421986

    Install the hood rear outer air inlet seal (2) to the left and right side.

  23. Install the 2 hood rear outer air inlet seal retainers (1) to the left and right side.
  24. GM5417116

    Air Inlet Grille Panel Extension (1) - Install [2x]

    1. Install the air inlet grille panel extension (1).
    2. Remove the masking tape from the top edge of the service part.
    3. Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.
  25. GM5325063

    Windshield Wiper Arm (3) - Install [2x]

    1. Clean the windshield wiper transmission pivot shaft splines with a soft wire brush before installing the windshield wiper arm (3).
    2. Position the windshield wiper arm (3) on the windshield wiper transmission pivot shaft.
    3. Windshield Wiper Arm Nut (2) - Install and tighten - Fastener Specifications
    4. Windshield Wiper Arm Finish Cap (1) - Install
  26. GM5416557

    If required, realign the windshield wipers to their respective alignment circles (1) on the windshield.

    1. Lubricate the windshield with clean washer fluid.
    2. Run the windshield wipers for two complete cycles then turn off the windshield wipers.
    3. Ensure the windshield wipers are in the full park position.
    4. Inspect the windshield wipers for proper position to the alignment circles (1) on the windshield.
  27. Fill the cooling system to the proper level. Cooling System Draining and Filling (LSY GE 47716) , or Cooling System Draining and Filling (LSY Static Fill) , or Cooling System Draining and Filling (LSY with V03 Static Fill) , or Cooling System Draining and Filling (L3B Static Fill) , or Cooling System Draining and Filling (L3B GE 47716) , or Cooling System Draining and Filling (LSY with V03 GE 47716) , or Cooling System Draining and Filling (LF4 Static Fill) , or Cooling System Draining and Filling (LF4 GE 47716)
  28. Start the engine and check for leaks.
scientia non olet · About LEMON Manuals