LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 127 (Engine Controls And Fuel - 3.6L (LF4) - Repair Instructions (2 Of 3)) >> Repair Instructions >> Fuel Feed Intermediate Pipe Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5869756Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Do NOT reuse the fuel feed intermediate pipe. If the fuel feed intermediate pipe fittings are loosened or the pipes are removed, the pipes MUST be replaced.

    Fuel Feed Intermediate Pipe (1) - Install NEW

    1. Slide fuel feed pipe fitting nuts (2) back along fuel feed intermediate pipe (1) to reveal the formed ends (3) of the fuel feed pipe.
    2. Carefully install the formed ends (3) of the fuel feed intermediate pipe into the sockets of the fuel pump (4) and the fuel injection fuel rails (5).
    3. Hold the pipe firmly in place and hand tighten the fuel feed pipe fitting nuts (2) onto the threads on the fuel injection fuel rails (5) and the fuel pump (4).
    2. CAUTION:

    Refer to Fastener Caution .

  2. Fuel Feed Intermediate Pipe Nut (2) @ Fuel Feed Intermediate Pipe (1) - Tighten [3x] - Fastener Specifications
  3. GM5869727Courtesy of GENERAL MOTORS COMPANY
    WARNING:

    The noise cancelling foam component MUST be replaced if it has been exposed to engine fluids. Failure to replace the noise cancelling foam component that has been exposed to engine fluids may result in an engine fire resulting in catastrophic engine damage, and possible injury or death.

    Engine Rear Noise Shield (1) - Install

  4. GM4044075Courtesy of GENERAL MOTORS COMPANY

    Fuel Pipe Shield (1) - Install

  5. GM5869276Courtesy of GENERAL MOTORS COMPANY

    Wiring Harness (3) - Install

  6. Retainer (2) - Install [3x]
  7. Engine Rear Noise Shield Bolt (1) - Install and tighten [2x] - Fastener Specifications
  8. GM4044046Courtesy of GENERAL MOTORS COMPANY

    Engine Rear Noise Shield Bolt (1) - Install and tighten - Fastener Specifications

  9. GM5524604Courtesy of GENERAL MOTORS COMPANY

    Install the plenum front panel (3) to the dash panel upper insulator (2).

    10. NOTE:

    This is a push nut.

  10. Plenum Panel Nut (1) - Install [9x]
  11. GM5865881Courtesy of GENERAL MOTORS COMPANY

    Plenum Front Panel (1) - Install

  12. GM5865879Courtesy of GENERAL MOTORS COMPANY

    Plenum Front Panel Bolt (1) - Install and tighten [4x] - Fastener Specifications

  13. Plenum Front Panel Nut (2) - Install and tighten [3x]

    - Fastener Specifications

  14. GM5422039Courtesy of GENERAL MOTORS COMPANY

    Plenum Front Panel Nut (1) - Install and tighten [3x] - Fastener Specifications

  15. Plenum Front Panel Bolt (2) - Install and tighten [3x] - Fastener Specifications
  16. Install the forward lamp wiring harness extension (3) into the plenum front panel.
  17. Connect the electrical connector.
  18. GM5499583Courtesy of GENERAL MOTORS COMPANY

    Air Inlet Deflector Water Deflector (1) - Install

  19. GM5499581Courtesy of GENERAL MOTORS COMPANY

    Air Inlet Deflector Water Deflector Retainer (1) - Install [2x]

  20. GM5420344Courtesy of GENERAL MOTORS COMPANY

    Install the windshield wiper system module (2) in the vehicle.

  21. Windshield Wiper System Module Bolt (1) - Install and tighten [2x] Fastener Specifications
  22. Connect the windshield wiper motor electrical connector.
  23. Connect the battery negative cable. - Battery Negative Cable Disconnection and Connection
  24. GM5420286Courtesy of GENERAL MOTORS COMPANY

    Windshield Wiper System Module Shield (1) - Install

  25. GM5417442Courtesy of GENERAL MOTORS COMPANY

    Air Inlet Grille Panel (2) - Install

    1. Install the air inlet grille panel (2) between both hood hinges.
    2. Connect the windshield washer nozzle hose to the windshield washer pump hose.
    3. Air Inlet Grille Panel Retainer (1) - Install [6x]
  26. GM5862927Courtesy of GENERAL MOTORS COMPANY

    Front Compartment Side Sight Shield (2) - Install

  27. Front Compartment Side Sight Shield Retainer (1) - Install [3x]
  28. GM5865291Courtesy of GENERAL MOTORS COMPANY

    Air Inlet Grille Panel Extension (2) - Install

  29. Air Inlet Grille Panel Retainer (1) - Install [2x]
  30. GM5421986Courtesy of GENERAL MOTORS COMPANY

    Install the hood rear outer air inlet seal (2) to the left and right side.

  31. Install the 2 hood rear outer air inlet seal retainer (1) to the left and right side.
  32. GM5417116Courtesy of GENERAL MOTORS COMPANY

    Air Inlet Grille Panel Extension (1) - Install [2x]

    1. Install the air inlet grille panel extension (1).
    2. Remove the masking tape from the top edge of the service part.
    3. Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.
  33. GM5325063Courtesy of GENERAL MOTORS COMPANY

    Windshield Wiper Arm (3) - Install [2x]

    1. Clean the windshield wiper transmission pivot shaft splines with a soft wire brush before installing the windshield wiper arm (3).
    2. Position the windshield wiper arm (3) on the windshield wiper transmission pivot shaft.
    3. Windshield Wiper Arm Nut (2) - Install and tighten Fastener Specifications
    4. Windshield Wiper Arm Finish Cap (1) - Install
  34. GM5416557Courtesy of GENERAL MOTORS COMPANY

    If required, realign the windshield wipers to their respective alignment circles (1) on the windshield.

    1. Lubricate the windshield with clean washer fluid.
    2. Run the windshield wipers for two complete cycles then turn off the windshield wipers.
    3. Ensure the windshield wipers are in the full park position.
    4. Inspect the windshield wipers for proper position to the alignment circles (1) on the windshield.
  35. Pressurize the fuel system and inspect for leaks.
scientia non olet · About LEMON Manuals