LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 107 (Power Seats) >> Diagnostic Information and Procedures >> Power Seat Malfunction (Power Seat Malfunction (Passenger with AHH or AKE)) >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition/Vehicle OFF, disconnect the X1 connector at the K40P Passenger Seat Adjuster Memory Module.
  2. Test for less than 10 Ω between ground circuit terminal 1 and ground.
    • If 10 Ω or greater 
    1. Test circuit 2250 for an open/high resistance.
      • If an open/high resistance is found, repair the fault on the circuit.
      • Go to next step: If an open/high resistance is not found
    2. Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  3. Ignition/Vehicle in Service Mode.
  4. Verify a test lamp illuminates between the B+ circuit terminal 6 and ground.
    • If the test lamp does not illuminate. 
    1. Test circuit 5340 for a short to ground.
      • If a short to ground is found, repair the fault on the circuit.
      • Go to next step: If a short to ground is not found
    2. Test circuit 5340 for an open/high resistance.
      • If an open/high resistance is found, repair the fault on the circuit.
      • Go to next step: If an open/high resistance is not found
    3. Verify the fuse is OK and there is voltage at the fuse.
    • Go to next step: If the test lamp illuminates. 
  5. Ignition/Vehicle OFF, connect the X1 connector at the K40P Passenger Seat Adjuster Memory Module and disconnect the connector at the appropriate seat motor(s) listed below:
    • M50P Front Seat Tilt Adjuster Actuator - Passenger
    • M51P Front Seat Adjuster Actuator - Passenger
    • M55P Front Seat Vertical Adjuster Actuator - Passenger
    • M56P Front Seat Recliner Actuator - Passenger
  6. Connect a test lamp between control circuit terminal 1 and control circuit terminal 3.
  7. Ignition/Vehicle in Service Mode.
  8. Verify the test lamp turns ON while operating the appropriate seat switch in the Up/Down or Forward/Rearward directions.
    • If the test lamp remains OFF during either of the commands 
    1. Test the appropriate circuits listed below for a short to ground:
      • M50P Front Seat Tilt Adjuster Actuator - Passenger = Circuit 297 and circuit 298
      • M51P Front Seat Adjuster Actuator - Passenger = Circuit 290 and circuit 296
      • M55P Front Seat Vertical Adjuster Actuator - Passenger = Circuit 288 and circuit 289
      • M56P Front Seat Recliner Actuator - Passenger = Circuit 76 and circuit 77
      • If a short to ground is found, repair the fault on the circuit.
      • Go to next step: If a short to ground is not found
    2. Test the appropriate circuits listed below for an open/high resistance:
      • M50P Front Seat Tilt Adjuster Actuator - Passenger = Circuit 297 and circuit 298
      • M51P Front Seat Adjuster Actuator - Passenger = Circuit 290 and circuit 296
      • M55P Front Seat Vertical Adjuster Actuator - Passenger = Circuit 288 and circuit 289
      • M56P Front Seat Recliner Actuator - Passenger = Circuit 76 and circuit 77
      • If an open/high resistance is found, repair the fault on the circuit.
      • Go to next step: If an open/high resistance is not found
    3. Replace the K40P Passenger Seat Adjuster Memory Module.
    • Go to next step: If the test lamp turns ON during each of the commands 
  9. Test or replace the appropriate seat motor listed below:
    • M50P Front Seat Tilt Adjuster Actuator - Passenger
    • M51P Front Seat Adjuster Actuator - Passenger
    • M55P Front Seat Vertical Adjuster Actuator - Passenger
    • M56P Front Seat Recliner Actuator - Passenger
scientia non olet · About LEMON Manuals