LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2018 >> Escalade Base, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 5 (Engine Controls And Fuel - 6.0L (L96) - DTC P0010 To DTC P0341) >> Diagnostic Information And Procedures >> DTC P0340 Or P0341: Intake Camshaft Position Sensor >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2018 Chevrolet Suburban 3500 HD. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition/Vehicle & All vehicle systems - Off
    NOTE: It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.
  2. Disconnect the appropriate electrical connector: B23 Camshaft Position Sensor
  3. Test for less than 10 Ω between the test points: Low Reference circuit terminal 2/B & Ground
    • If 10 Ω or greater 
    1. Disconnect the electrical connector: K20 Engine Control Module
    2. Test for less than 2 Ω between the test points: Low Reference circuit terminal 2/B @ Component harness & The other end of the circuit @ Control module harness
      • If 2 Ω or greater - Repair the open/high resistance in the circuit.
      • If less than 2 Ω - Replace the component: K20 Engine Control Module
    • Go to next step: If less than 10 Ω 
  4. Ignition - On/Vehicle - In Service Mode
  5. Test for 4.8 to 5.2 V between the test points: 5 V Reference circuit terminal 1/A & Ground
    • If less than 4.8 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Test for infinite resistance between the test points: 5 V Reference circuit terminal 1/A @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    4. Test for less than 2 Ω between the test points: 5 V Reference circuit terminal 1/A @ Component harness & The other end of the circuit @ Control module harness
      • If 2 Ω or greater - Repair the open/high resistance in the circuit.
      • If less than 2 Ω - Replace the component: K20 Engine Control Module
    • If greater than 5.2 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: 5 V Reference circuit terminal 1/A @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: K20 Engine Control Module
    • Go to next step: If between 4.8 and 5.2 V 
  6. Test for 4.8 to 5.2 V between the test points: Signal circuit terminal 3/C & Ground
    • If less than 4.8 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Test for infinite resistance between the test points: Signal circuit terminal 3/C @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    4. Test for less than 2 Ω between the test points: Signal circuit terminal 3/C @ Component harness & The other end of the circuit @ Control module harness
      • If 2 Ω or greater - Repair the open/high resistance in the circuit.
      • If less than 2 Ω - Replace the component: K20 Engine Control Module
    • If greater than 5.2 V 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: K20 Engine Control Module
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 3/C @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V - Replace the component: K20 Engine Control Module
    • Go to next step: If between 4.8 and 5.2 V 
  7. Verify DTC P0341 is not set.
    • If the DTC is set 

      Verify the following conditions do not exist:

    • B23 Camshaft Position Sensor & Reluctor Ring - Excessive play/Foreign material passing between the components/Incorrect air gap/Incorrect installation/Loose/Visible Damage
    • Engine Oil - Contaminated/Dirty
    • Timing Chain or Timing Belt - Visible Damage/Worn
    • Timing Chain Tensioner or Timing Belt Tensioner - Visible Damage/Worn
      • If a condition exists - Repair or replace as necessary
      • If no condition exists - Test or replace the component: B23 Camshaft Position Sensor
    • Go to next step: If the DTC is not set 
  8. Test or replace the component: B23 Camshaft Position Sensor
scientia non olet · About LEMON Manuals