LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2018 >> Escalade Base, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 5 (Engine Controls And Fuel - 6.0L (L96) - DTC P0010 To DTC P0341) >> Diagnostic Information And Procedures >> DTC P0112, P0113 Or P0114: Intake Air Temperature (IAT) Sensor 1 Circuit >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2018 Chevrolet Suburban 3500 HD. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF and all systems OFF, it may take up to for 2 min for all vehicle systems to power down. Disconnect the harness connector at the B75C Multifunction Intake Air Sensor.
  2. Test for less than 2 Ω between the low reference circuit terminal 3 and ground.
    • If 2 Ω or greater 
    1. Disconnect the harness connector at the K20 Engine Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open or high resistance in the circuit.
      • If less than 2 Ω replace the K20 Engine Control Module.
    • Go to next step: If less than 2 Ω 
  3. Ignition ON.
  4. Test for 4.8 - 5.2 V between the intake air temperature sensor 1 signal circuit terminal 1 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module, ignition ON.
      NOTE: If the signal circuit is shorted to a voltage the engine control module or the sensor may be damaged.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K20 Engine Control Module.
    • Go to next step: If between 4.8 - 5.2 V 
  5. Verify the scan tool IAT Sensor 1 parameter is colder than -39°C (-38°F).
    • If warmer than -39°C (-38°F). 
    1. Ignition OFF, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit terminal 1 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • Go to next step: If colder than -39°C (-38°F). 
  6. Ignition OFF, install a 3 A fused jumper wire between the signal circuit terminal 1 and the low reference circuit terminal 3, ignition ON.
  7. Verify the scan tool IAT Sensor 1 parameter is warmer than 149°C (300°F).
    • If colder than 149°C (300°F). 
    1. Ignition OFF, remove the jumper wire, disconnect the harness connector at the K20 Engine Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • Go to next step: If warmer than 149°C (300°F). 
  8. Test or replace the B75C Multifunction Intake Air Sensor.
scientia non olet · About LEMON Manuals