Engine Mechanical - 4.8L, 5.3L, 6.0L Or 6.2L (4 Of 5)

• Off-Vehicle Repair Instructions (2 Of 3)
  • Crankshaft Balancer Cleaning and Inspection
  • Automatic Transmission Flex Plate Cleaning and Inspection
  • Piston and Connecting Rod Disassemble
  • Piston, Connecting Rod, and Bearing Cleaning and Inspection
    • Piston, Pin, and Piston Rings
    • Measuring Piston Ring End Gap
    • Connecting Rod and Bearings
  • Piston and Connecting Rod Assemble
  • Camshaft Bearing Removal
    • Tools Required
    • Procedure
    • Tool Usage Information
      • Bearing, Expander, and Expander Driver Information
      • Tool Assembly and Operation
  • Camshaft and Bearings Cleaning and Inspection (RPO LY2/LC9/LY5/LMG)
    • Notes
    • Procedure
    • Measuring Camshaft Lobe Lift
  • Camshaft and Bearings Cleaning and Inspection (RPO LY6/L76/L92)
    • Notes
    • Clean/Inspection Procedure
    • Measuring Camshaft Lobe Lift
  • Camshaft Bearing Installation
    • Tools Required
    • Procedure
  • Camshaft Timing Chain and Sprocket Cleaning and Inspection
  • Camshaft Position Actuator Cleaning and Inspection
  • Camshaft Position Actuator Magnet Cleaning and Inspection
  • Camshaft Position Actuator Solenoid Valve Inspection (On-Vehicle)
  • Camshaft Position Actuator Solenoid Valve Inspection (Off-Vehicle)
  • Valve Rocker Arm and Push Rod Cleaning and Inspection
  • Valve Lifter and Guide Cleaning and Inspection (RPO LY2/LY6/L92)
    • Valve Lifters
    • Valve Guides
  • Valve Lifter and Guide Cleaning and Inspection (RPO LC9/LY5/LMG/L76)
    • Non Active Fuel Management Valve Lifters
    • Active Fuel Management Valve Lifters
    • Valve Guides
  • Cylinder Head Disassemble
    • Special Tools
    • Procedure
  • Cylinder Head Cleaning and Inspection
    • Notes
    • Cleaning/Inspection Procedure
  • Valve Guide Reaming, and Valve and Seat Grinding
    • Tools Required
    • Valve Guide Reaming
    • Valve and Seat Grinding
  • Cylinder Head Assemble
    • Special Tools
    • Procedure
  • Oil Pump Disassemble
  • Oil Pump Cleaning and Inspection
  • Oil Pump Assemble
  • Engine Front Cover Cleaning and Inspection (RPO LY2/LC9/LY5/LMG)
  • Engine Front Cover Cleaning and Inspection (RPO LY6/L76/L92)
  • Crankshaft Rear Oil Seal Housing Cleaning and Inspection
  • Engine Block Valley Cover Cleaning and Inspection
  • Valve Lifter Oil Manifold Cleaning and Inspection
  • Valve Rocker Arm Cover Cleaning and Inspection
  • Oil Pan Cleaning and Inspection
  • Intake Manifold Cleaning and Inspection
    • Cleaning Procedure
    • Inspection Procedure
  • Exhaust Manifold Cleaning and Inspection
  • Engine Coolant Air Bleed Pipe and Hole Cover Cleaning and Inspection
  • Water Pump Cleaning and Inspection
  • Thread Repair
    • Notes
    • General Thread Repair
    • Cylinder Head Bolt Hole Thread Repair
    • Main Cap Bolt Hole Thread Repair
  • Service Prior to Assembly
  • Engine Block Plug Installation
  • Crankshaft and Bearing Installation
    • Tools Required
    • Procedure
  • Piston, Connecting Rod, and Bearing Installation
    • Notes
    • Piston Selection
    • Piston, Pin, and Connecting Rod Installation
  • Camshaft Installation
  • Camshaft Position Actuator and Solenoid Valve Installation
    • Notes
    • Procedure
  • Timing Chain and Sprocket Installation
    • Notes
    • Procedure
  • Oil Pump, Screen and Crankshaft Oil Deflector Installation (RPO LY2/LC9/LY5/LMG)
  • Oil Pump, Screen and Crankshaft Oil Deflector Installation (RPO LY6/L76/L92)
  • Crankshaft Rear Oil Seal Housing Installation (Without Seal in Housing)
    • Notes
    • Procedure
  • Crankshaft Rear Oil Seal Housing Installation (With Seal in Housing)
    • Notes
    • Procedure
  • Crankshaft Rear Oil Seal Installation
    • Notes
    • Procedure
  • Engine Front Cover Installation (RPO LY2/LC9/LY5/LMG)
    • Notes
    • Procedure
  • Engine Front Cover Installation (RPO LY6/L76/L92)
    • Notes
    • Procedure