LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2007 >> Escalade ESV >> Repair and Diagnosis >> External Pages >> Different car >> Section 969 (Automatic Transmission - 4L60-E/4L65-E/4L70-E - Removal & Installation, Service, Overhaul, Troubleshooting & Diagnosis) >> On-Vehicle Repair Instructions >> Transmission Fluid Filler Tube and Seal Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2007 GMC Sierra and 2007 Chevrolet Silverado. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: View Of Transmission Oil Level Indicator Tube At Transmission
    GM1284302Courtesy of GENERAL MOTORS CORP.
  1. Install a NEW seal to the indicator tube.
  2. Install the oil level indicator tube, if equipped with RPO HP2.
    3. Fig 2: View Of Oil Level Indicator Tube & Seal
    GM396798Courtesy of GENERAL MOTORS CORP.
  3. Install a NEW seal to the indicator tube.
  4. Install the oil level indicator tube.
    5. Fig 3: View Of Transmission Oil Level Indicator Tube Bolt
    GM1284303Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice .
  5. Install the indicator tube bolt, if equipped with RPO HP2.

    Tighten:  Tighten the bolt to 18 N.m (13 lb ft).

    6. Fig 4: View Of Oil Level Indicator Tube Nut
    GM396797Courtesy of GENERAL MOTORS CORP.
  6. Install the indicator tube nut.

    Tighten:  Tighten the nut to 18 N.m (13 lb ft).

    7. Fig 5: View Of Transmission Oil Cooler Lines
    GM1705100Courtesy of GENERAL MOTORS CORP.
  7. Remove the plugs from the transmission oil cooler line fittings.
  8. Connect the transmission oil cooler lines. Refer to Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection .
    9. Fig 6: View Of Transmission Heat Shield Bolts & Shield
    GM394459Courtesy of GENERAL MOTORS CORP.
  9. Remove the transmission heat shield.

    Tighten:  Tighten the bolts to 17 N.m (12 lb ft).

    10. Fig 7: View Of Right Exhaust Pipe Nuts
    GM858553Courtesy of GENERAL MOTORS CORP.
  10. Tighten the right exhaust pipe nuts.

    Tighten:  Tighten the nuts to 50 N.m (37 lb ft).

    11. Fig 8: View Of Left Exhaust Manifold Pipe & Nuts
    GM858550Courtesy of GENERAL MOTORS CORP.
  11. Tighten the left exhaust pipe nuts.

    Tighten:  Tighten the nuts to 50 N.m (37 lb ft).

  12. Install the transmission crossmember. Refer to Transmission Support Crossmember Replacement (2WD 1500/2500) or Transmission Support Crossmember Replacement (2WD 2500 HD/3500) or Transmission Support Crossmember Replacement (4WD 1500/2500) or Transmission Support Crossmember Replacement (4WD 2500 HD/3500) .
  13. Remove the support from the transmission.
  14. Lower the vehicle.
    15. Fig 9: View Of Transmission Oil Level Indicator
    GM1284301Courtesy of GENERAL MOTORS CORP.
  15. Install the transmission oil level indicator.
  16. Lock the transmission oil level indicator.
  17. Install the intake manifold. Refer to Intake Manifold Replacement (L92 - First Design) or Intake Manifold Replacement (L92 - Second Design) or Intake Manifold Replacement (LY2 and LY6) or Intake Manifold Replacement (LH6, LMG, LY5 and L76) .
scientia non olet · About LEMON Manuals