LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2007 >> CTS V >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel System Displays And Gauges >> Diagnostic Information and Procedures >> Fuel Gage Inaccurate or Inoperative >> Test Description

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. 3:  This step tests for a high resistance in the primary fuel level sensor signal circuit and the low reference circuit of the fuel level sensors.
  2. 4:  This step tests for a high resistance in the secondary fuel level signal circuit and the low reference circuit of the fuel level sensors.
  3. 18:  DTCs will be set in the ECM when you perform this diagnostic table.
Fuel Gage Inaccurate or Inoperative

Step Action Values Yes No
Schematic Reference: Instrument Cluster Schematics 
Connector End View Reference: Engine Control Module Connector End Views for the 2.8L engine, Engine Control Module Connector End Views for the 3.6L engine or Inline Harness Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Turn ON the ignition, with the engine OFF.
  2. Install a scan tool.
  3. With the scan tool, perform the Displays Test in the instrument panel cluster (IPC) Special Functions Output Controls list.
Does the gage move from 0 to its maximum value and back to 0 when you perform the Displays Test?		 - Go to Step 3  Go to Step 16 
3 
  1. Disconnect C420, the fuel level sensor.
  2. Connect the J 33431-C  Signal Generator and Instrument Panel Tester between the signal circuit of the fuel level sensor signal primary and the low reference circuit of the fuel level sensors on the male terminal side.
  3. Turn ON the ignition, with the engine OFF.
    4. IMPORTANT: Verify the J 33431-C  resistance settings with a DMM.
  4. Vary the resistance on the J 33431-C  from 40-250 ohms.
  5. With the scan tool, observe the Fuel Level Sensor Right Volts parameter in ECM EVAP Data list.
  6. Refer to Fuel Level Specifications  in order to convert from resistance to Fuel Level Sensor Right Volts.
Does the Fuel Level Sensor Right Volts parameter change smoothly across the specified range?		 0.7-2.5 V Go to Step 4  Go to Step 10 
4 
  1. Connect the J 33431-C  between the signal circuit of the fuel level sensor signal secondary and the low reference circuit of the fuel level sensors on the male terminal side.
  2. Turn the ignition ON, with the engine OFF.
    3. IMPORTANT: Verify the J 33431-C  resistance settings with a DMM.
  3. Vary the resistance on the J 33431-C  from 40-250 ohms.
  4. With the scan tool, observe the Fuel Level Sensor Left Volts parameter in ECM EVAP Data list.
  5. Refer to Fuel Level Specifications  in order to convert from resistance to Fuel Level Sensor Left Volts.
Does the Fuel Level Sensor Left Volts parameter change smoothly across the specified range?		 0.7-2.5 V Go to Step 5  Go to Step 11 
5 Inspect for the following items:
  • A poor connection at the harness connector of the suspect fuel level sensor-Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
  • A high resistance in the fuel level sensor signal primary signal circuit or the low reference circuit between the fuel level sensors and C420
  • A high resistance in the fuel level sensor signal secondary signal circuit or the low reference circuit between the fuel level sensors and C420
  • A misaligned fuel level sender
  • A deformed fuel tank

Did you find and correct the condition?		 - Go to Step 18  Go to Step 6 
6
  1. Remove the primary fuel level sender.
  2. Inspect for the following items:
    • A stuck fuel level sensor-For example, the fuel strainer interfering with the sender float arm
    • Foreign material in the fuel tank, i.e. ice
Did you find and correct the condition?		 - Go to Step 18  Go to Step 7 
7
  1. With the DMM, measure the resistance of the primary fuel level sensor while moving the float arm.
  2. Observe both the analog and digital displays on the DMM.
Does the resistance change smoothly across the specified range?		 40-250 Ω Go to Step 8  Go to Step 14 
8
  1. Remove the secondary fuel level sender.
  2. Inspect for the following items:
    • A stuck fuel level sensor-For example, the fuel strainer interfering with the sender float arm
    • Foreign material in the fuel tank, i.e. ice
Did you find and correct the condition?		 - Go to Step 18  Go to Step 9 
9
  1. With the DMM, measure the resistance of the secondary fuel level sensor while moving the float arm.
  2. Observe both the analog and digital displays on the DMM.
Does the resistance change smoothly across the specified range?		 40-250 Ω Go to Diagnostic Aids In This Test Go to Step 15 
10 Test the fuel level sensor signal primary signal circuit for a high resistance. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 18  Go to Step 12 
11 Test the fuel level sensor signal secondary signal circuit for a high resistance. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 18  Go to Step 13 
12 Test the low reference circuit of the fuel level sensors for a high resistance. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 18  Go to Step 13 
13 Inspect for poor connections at the harness connector of the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 18  Go to Step 17 
14 Replace the primary fuel level sensor. Refer to Fuel Level Sensor Replacement - Primary for the 2.8L engine or Fuel Level Sensor Replacement - Primary for the 3.6L engine.
Did you complete the replacement?		 - Go to Step 18  -
15 Replace the secondary fuel level sensor. Refer to Secondary Fuel Tank Module Replacement for the 2.8L engine or Secondary Fuel Tank Module Replacement for the 3.6L engine.
Did you complete the replacement?		 - Go to Step 18  -
16 Replace the IPC. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 18  -
17 Replace the ECM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 18  -
18 
  1. Use the scan tool in order to clear the ECM DTCs.
  2. Operate the system in order to verify the repair.
Did you correct the condition?		 - System OK Go to Step 2 
scientia non olet · About LEMON Manuals