Poor Fuel Economy

WARNING: This page is about a different variant/trim than selected.

Poor Fuel Economy

Inspections	Action
DEFINITION: Fuel economy, as measured by an actual road test, is noticeably lower than expected. Also, fuel economy is noticeably lower than the economy was on this vehicle at one time, as previously shown by an actual road test.
Preliminary	Refer to Important Preliminary Inspections Before Starting in Symptoms - Engine Controls . Search for bulletins. Inspect the engine control module (ECM) grounds for being clean, tight, and in the proper locations. Refer to Power and Grounding Component Views in Wiring Systems and Engine Controls Schematics . Discuss driving habits with the owner. Is the A/C ON or the Defroster mode ON full time? Are the tires at the correct pressure? Are the wheels and tires the correct size? Are there excessively heavy loads being carried? Is the acceleration rate too much, too often? Remove the air filter element and inspect for dirt or for restrictions. Refer to Air Cleaner Element Replacement . Replace as necessary.
Fuel System	Discuss with the owner the type, quality, and alcohol content of the fuel. Oxygenated fuels have lower energy and may deliver reduced fuel economy. Test the fuel injectors. Refer to Fuel Injector Balance Test with Special Tool or Fuel Injector Solenoid Coil Test . Test for incorrect fuel pressure. Refer to Fuel System Diagnosis . Inspect for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis (W/Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (W/O Special Tool) . Inspect that each fuel injector harness is connected to the correct injector and cylinder. Relocate the injector harnesses as necessary. Inspect for the following conditions that may cause the engine to run rich: NOTE: Refer to Heated Oxygen and Oxygen Sensor Notice in Cautions and Notices. Water intrusion in the heated oxygen sensor (HO2S) connector Engine oil contaminated by fuel An evaporative emission (EVAP) canister purge condition Incorrect fuel pressure-Refer to Fuel System Diagnosis . Leaking fuel injectors-Refer to Fuel System Diagnosis . For proper operation of the manifold absolute pressure (MAP) sensor-Refer to Scan Tool Data Definitions . For proper operation of the mass air flow (MAF) sensor Blockage on the inlet screen of the MAF sensor Vacuum hoses that are split, kinked, or improperly connected An air intake duct that is collapsed or restricted An air filter that is dirty or restricted-Refer to Air Cleaner Element Replacement .
Sensor/System	Inspect the air intake system and crankcase for air leaks. Verify that the engine coolant temperature (ECT) sensor is not shifted in value. Refer to Temperature Versus Resistance for resistance specifications. Inspect for an inaccurate speedometer. Refer to Symptoms - Instrument Panel, Gages and Console in Instrument Panel, Gages, and Console. Use a scan tool in order to monitor the knock sensor (KS) system for excessive spark retard activity. Refer to Scan Tool Data Definitions .
Ignition System	Inspect for proper ignition voltage output with the J 26792 Spark Tester. Refer to Electronic Ignition (EI) System Diagnosis . Remove the spark plugs and inspect for the following conditions: Wet plugs Cracks Wear Improper gap Burned electrodes Heavy deposits Refer to Spark Plug Inspection . An improper spark plug gap will cause a driveability problem. Gap the spark plugs using a wire gage gap tool. Refer to Spark Plug Replacement and Ignition System Specifications . Determine the cause of the fouling before replacing the spark plugs. Soaking the secondary ignition system with water from a spray bottle may help locate damaged or deteriorated components. Look and listen for arcing or misfiring as you apply water. Inspect for loose ignition coil grounds. Refer to Power and Grounding Component Views in Wiring Systems.
Engine Cooling System	Inspect the engine coolant level for being low. Refer to Loss of Coolant (LH2 and LY7) or Loss of Coolant (LC3) in Engine Cooling. Inspect the engine thermostat for proper operation and for the correct heat range. Refer to Thermostat Diagnosis in Engine Cooling.
Engine Mechanical	Inspect engine mechanical for the following conditions: Compression Sticking or leaking valves Worn camshaft lobes Valve timing Worn rocker arms Broken valve springs Excessive oil in combustion chamber-Leaking valve seals. For more information refer to one of the following procedures: Engine Compression Test Symptoms - Engine Mechanical Oil Consumption Diagnosis For incorrect basic engine parts inspect for the following components: The camshaft-Refer to Camshaft Cleaning and Inspection in Engine Mechanical. The cylinder heads-Refer to Cylinder Head Cleaning and Inspection in Engine Mechanical. The pistons, etc.-Refer to Piston, Connecting Rod, and Bearing Cleaning and Inspection in Engine Mechanical. Refer to Symptoms - Engine Mechanical in Engine Mechanical for diagnostic procedures.
Additional Inspections	Visually and physically check the vacuum hoses for splits, kinks, and proper connections and routing as shown on Vehicle Emission Control Information label. Inspect the transmission torque converter clutch (TCC) operation. The scan tool should indicate a RPM drop, when the system commands the TCC ON. Inspect the exhaust system for a possible restriction. Inspect for the following conditions: The exhaust system for damaged or collapsed pipes The mufflers for heat distress or possible internal failure For possible plugged catalytic converters-Refer to Restricted Exhaust in Engine Exhaust. Electromagnetic interference (EMI) on the reference circuit can cause an engine miss condition. A scan tool can usually detect EMI by monitoring the engine RPM. A sudden increase in RPM with little change in actual engine RPM change indicates EMI is present. Inspect for high voltage components, near ignition control circuits, if a condition exists. Inspect the brake system for dragging or improper operation. Refer to Symptoms - Hydraulic Brakes in Hydraulic Brakes. Verify that the vehicle operator does not drive with a foot on the brake pedal.