Lack of Power, Sluggishness, or Sponginess

WARNING: This page is about a different variant/trim than selected.

Lack of Power, Sluggish or Spongy

Inspection/Tests	Action
DEFINITION: Engine delivers less than expected power. Little or no increase in speed when the accelerator pedal is pushed down part way.
Preliminary Inspections	Refer to Important Preliminary Inspections Before Starting in Symptoms - Engine Controls . Search for bulletins. Inspect the engine control module (ECM) grounds for being clean, tight, and in the proper locations. Refer to Power and Grounding Component Views in Wiring Systems and Engine Controls Schematics . Remove the air filter element and inspect for dirt or for restrictions. Refer to Air Cleaner Element Replacement and replace as necessary.
Fuel System	Test for incorrect fuel pressure. Refer to Fuel System Diagnosis . Inspect for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis (W/Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (W/O Special Tool) . Test the fuel injectors. Refer to Fuel Injector Balance Test with Special Tool or Fuel Injector Solenoid Coil Test . Inspect for the following conditions that may cause the engine to run rich: NOTE: Refer to Heated Oxygen and Oxygen Sensor Notice in Cautions and Notices. Water intrusion in the heated oxygen sensor (HO2S) connector Engine oil contaminated by fuel An evaporative emission (EVAP) canister purge condition Incorrect fuel pressure-Refer to Fuel System Diagnosis . Leaking fuel injectors-Refer to Fuel System Diagnosis . Inspect for proper operation of the mass air flow (MAF) sensor. Refer to Scan Tool Data Definitions . Blockage on the inlet screen of the MAF sensor Vacuum hoses that are split, kinked, or improperly connected An air intake duct that is collapsed or restricted An air filter that is dirty or restricted-Refer to Air Cleaner Element Replacement . Inspect for the following conditions that may cause the engine to run lean: NOTE: Refer to Heated Oxygen and Oxygen Sensor Notice in Cautions and Notices. Water intrusion in the HO2S connector An exhaust leak between the HO2S and the engine-Refer to Exhaust Leakage in Engine Exhaust. Vacuum leaks Incorrect fuel pressure-Refer to Fuel System Diagnosis . Restricted fuel injectors-Refer to Fuel Injector Balance Test with Special Tool . Inspect for proper operation of the MAF sensor. Refer to Scan Tool Data Definitions . Fuel contamination-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (W/Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (W/O Special Tool) . Vacuum hoses that are split, kinked, or improperly connected
Sensor/System	Use a scan tool in order to monitor the knock sensor (KS) system for excessive spark retard activity. Refer to Scan Tool Data Definitions . Inspect for a dirty or damaged air cleaner element. Inspect for a collapsed or damaged intake air duct.
Ignition System	Soak the secondary ignition system with water from a spray bottle. Soaking the secondary ignition system may help locate damaged or deteriorated components. Look and listen for arcing or misfiring as water is applied. Monitor the Misfire Current Counters while driving the vehicle within the conditions that the misfire occurred. Inspect for proper ignition voltage output with the J 26792 Spark Tester. Remove the spark plugs and inspect for the following conditions: Correct heat range Wet plugs Cracks Wear Improper gap Burned electrodes Heavy deposits Refer to Spark Plug Inspection . An improper spark plug gap will cause a driveability problem. Gap the spark plugs using a wire gage gap tool. Refer to Ignition System Specifications and Spark Plug Replacement . Determine the cause of the fouling before replacing the spark plugs. Inspect the spark plug boots for signs of arcing, cracks, carbon tracking, or damage. Inspect for loose ignition coil ground.
Engine Mechanical	Inspect for incorrect camshaft timing. Refer to Setting Camshaft Timing in Engine Mechanical. Inspect for excessive oil in the combustion chambers and leaking valve seals. Refer to Oil Consumption Diagnosis in Engine Mechanical. Test cylinder compression. Refer to Engine Compression Test in Engine Mechanical. Inspect for incorrect basic engine parts, including the following components: The camshaft-Refer to Camshaft Cleaning and Inspection in Engine Mechanical. The cylinder heads-Refer to Cylinder Head Cleaning and Inspection in Engine Mechanical. The pistons, etc.-Refer to Piston, Connecting Rod, and Bearing Cleaning and Inspection in Engine Mechanical. Inspect for excessive crankshaft endplay that will cause the crankshaft position (CKP) sensor reluctor wheel to move out of alignment with the CKP sensor. Refer to Crankshaft and Bearing Cleaning and Inspection in Engine Mechanical. This could result in any of the following conditions: A no start A start and stall Erratic performance
Additional Inspections	Inspect the exhaust system for possible restrictions. Refer to Restricted Exhaust in Engine Exhaust. Inspect the exhaust system for damaged or collapsed pipes. Inspect the mufflers for heat distress or internal failure. Inspect the transmission torque converter clutch (TCC) for proper operation.