Conditions for Clearing the MIL/DTC

WARNING: This page is about a different variant/trim than selected.

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
Clear the MIL and the DTC with a scan tool.

DTC P0223

Step	Action	Value	Yes	No
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views
1	Did you perform the Diagnostic System Check - Vehicle?	-	Go to Step 2	Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2	Turn ON the ignition, with the engine OFF. Observe the throttle position (TP) sensor 2 parameter with a scan tool. Is the TP sensor 2 voltage more than the specified value?	4.6 V	Go to Step 3	Go to Step 4
3	Turn OFF the ignition. Disconnect the throttle body harness connector. Connect a test lamp between the signal circuit of TP sensor 2 and a good ground. Turn ON the ignition, with the engine OFF. Observe the TP sensor 2 parameter with a scan tool. Is the TP sensor 2 voltage less than the specified value?	0.2 V	Go to Step 6	Go to Step 12
4	Observe the Freeze Frame/Failure Records for this DTC. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze/Frame Failure Records. Did the DTC fail this ignition?	-	Go to Step 6	Go to Step 5
5	Observe the DTC Information with a scan tool. Slowly depress the accelerator pedal to wide-open throttle (WOT) and then slowly return it to the closed position. Repeat this action several times. Did the DTC fail this ignition?	-	Go to Step 18	Go to Intermittent Conditions
6	Turn OFF the ignition. Disconnect the throttle body harness connector. Turn ON the ignition, with the engine OFF. Measure the voltage from the 5-volt reference circuit of the TP sensors to a good ground with a DMM. Is the voltage within the specified range?	4.8-5.2 V	Go to Step 7	Go to Step 10
7	Turn OFF the ignition for 30 seconds. Allow the engine control module (ECM) to completely power down. This can be verified by the loss of communication on the scan tool. Measure the resistance from the low reference circuit of the TP sensors to a good ground with the DMM. Is the resistance less than the specified value?	5 ohm	Go to Step 14	Go to Step 8
8	Disconnect the ECM. Test the low reference circuit of the TP sensors for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	-	Go to Step 20	Go to Step 9
9	Measure the resistance from the case of the ECM to battery ground. Is the resistance less than the specified value?	5 ohm	Go to Step 16	Go to Step 17
10	Turn OFF the ignition. Disconnect the accelerator pedal position (APP) sensor harness connector. Turn ON the ignition, with the engine OFF. Measure the voltage from the 5-volt reference circuit of the TP sensors to a good ground with the DMM. Is the voltage within the specified range?	4.8-5.2 V	Go to Step 15	Go to Step 11
11	Test the 5-volt reference circuit of the TP sensor for an open or a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	-	Go to Step 20	Go to Step 13
12	Test the signal circuit of the TP sensor 2 for an open or a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	-	Go to Step 20	Go to Step 16
13	Test the 5-volt reference circuit of the APP sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	-	Go to Step 20	Go to Step 16
14	Test for an intermittent and for a poor connection at the throttle body sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition?	-	Go to Step 20	Go to Step 18
15	Test the signal circuit of APP sensor 2 for short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	-	Go to Step 20	Go to Step 16
16	Test for shorted terminals and poor connections at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition?	-	Go to Step 20	Go to Step 19
17	Repair the open or high resistance in the ECM ground circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair?	-	Go to Step 20	-
18	Replace the throttle body assembly. Refer to Throttle Body Assembly Replacement . Did you complete the replacement?	-	Go to Step 20	-
19	Replace the ECM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement?	-	Go to Step 20	-
20	Clear the DTCs with a scan tool. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze/Frame Failure Records. Did the DTC fail this ignition?	-	Go to Step 2	Go to Step 21
21	Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed?	-	Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information	System OK