Conditions for Running the DTC

WARNING: This page is about a different variant/trim than selected.

P0131

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Tank Level Remaining parameter is more than 10 percent.
The Throttle Position (TP) Indicated Angle parameter is between 0-50 percent.
The equivalence ratio is between 0.99-1.01.
DTC P0131 runs the lean test continuously when the above conditions are met for 3 seconds.

P0132

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Tank Level Remaining parameter is more than 10 percent.
The Throttle Position (TP) Sensor parameter is between 0-60 percent.
The equivalence ratio is between 0.99-1.01.
DTC P0132 runs the rich test continuously when the above conditions are met for 3 seconds.

P0137 or P0157

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Tank Level Remaining parameter is more than 10 percent.
The Power Enrichment parameter is active for more than 3 seconds.
The equivalence ratio is between 0.99-1.01.
These DTCs run the power enrichment test during each occurrence of power enrichment, when the above conditions are met for 3 seconds.

P0138 or P0158

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Tank Level Remaining parameter is more than 10 percent.
The TP Sensor parameter is between 0-50 percent.
The equivalence ratio is between 0.99-1.01.
These DTCs run the rich test continuously when the above conditions are met for 3 seconds.

P0151

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Tank Level Remaining parameter is more than 10 percent.
The Throttle Position (TP) Sensor parameter is between 0-50 percent.
The equivalence ratio is between 0.99-1.01.
DTC P0151 runs the test continuously when the above conditions are met for 3 seconds.

P0152

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Loop Status parameter is Closed.
The Ignition 1 Signal parameter is between 10-18 volts.
The Fuel Tank Level Remaining parameter is more than 10 percent.
The Throttle Position (TP) Sensor parameter is between 0-60 percent.
The equivalence ratio is between 0.99-1.01.
DTC P0152 runs the test continuously when the above conditions are met for 3 seconds.

P2A00

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
The Engine Run Time parameter is more than 100 seconds.
The Engine speed parameter is between 500-5,000 RPM.
The Ignition 1 Signal parameter is between 10-18 volts.
The Mass Airflow (MAF) Sensor parameter is between 3-30 g/s.
The ECT Sensor parameter is more than 70°C (158°F).
DTC P2A00 runs continuously when the above conditions are met for 5 seconds.

P2A01 or P2A04 Passive Test

DTCs P0030, P0036, P0053, P0054, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0131, P0132, P0133, P0134, P0135, P0137, P0138, P0140, P0141, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1516, P2101, P2119, P2135, P2176, P2A00 are not set.
The engine is running.
The Engine Run Time parameter is less than 260 seconds.
These DTCs run the passive test once per drive cycle when the above conditions are met for 2 seconds.

P2A01 or P2A04 Intrusive Test

DTCs P0030, P0036, P0053, P0054, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0131, P0132, P0133, P0134, P0135, P0137, P0138, P0140, P0141, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1516, P2101, P2119, P2135, P2176, P2A00 are not set.
The Engine Run Time parameter is more than 260 seconds.
The ignition 1 Signal parameter is between 10-18 volts.
The MAF sensor parameter is between 0.5-50 g/s.
The Engine Speed parameter is between 500-5,000 RPM.
The Vehicle Speed parameter is between 24-145 km/h (20-80 mph).
The Short Term FT parameter is between 5 and -5 percent.
These DTCs run the intrusive test once per drive cycle when the above conditions are met for 1 second.

P2A03

DTCs P0030, P0036, P0053, P0054, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0131, P0132, P0133, P0134, P0135, P0137, P0138, P0140, P0141, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1516, P2101, P2119, P2135, P2176, P2A00 are not set.
The Engine Run Time parameter is more than 100 seconds.
The ignition 1 Signal parameter is between 10-18 volts.
The MAF sensor parameter is between 3-30 g/s.
The Engine Speed parameter is between 500-5,000 RPM.
DTC P2A01 runs continuously when the above conditions are met for 5 seconds.