Cuts Out, Misses

WARNING: This page is about a different car, the 2006 GMC Yukon XL, 2006 Chevrolet Suburban, and 2006 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.

Cuts Out, Misses

Inspections	Action
DEFINITION: Steady pulsation or jerking that follows engine speed, usually more pronounced as engine load increases. This condition is not normally felt above 1,500 RPM or 48 km/h (30 mph). The exhaust has a steady spitting sound at idle or low speed.
Preliminary	Refer to Important Preliminary Inspections Before Starting in Symptoms - Engine Controls . Search for bulletins. Verify that the powertrain control module (PCM) grounds are clean, tight, and in the proper locations. Refer to Power and Grounding Component Views in Wiring Systems and Engine Controls Schematics . Remove the air filter element and inspect for dirt and for restrictions. Refer to Air Cleaner Element Replacement . Replace as necessary.
Fuel System	Test the fuel injectors. Refer to Fuel Injector Coil Test . Inspect for incorrect fuel pressure. Refer to Fuel System Diagnosis . Inspect for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (With Special Tool) . Inspect for the following that may cause the engine to run rich: NOTE: Refer to Heated Oxygen and Oxygen Sensor Notice in Cautions and Notices. Water intrusion in the heated oxygen sensor (HO2S) connector Engine oil contaminated by fuel An evaporative emission (EVAP) canister purge condition Incorrect fuel pressure-Refer to Fuel System Diagnosis . Leaking fuel injectors-Refer to Fuel System Diagnosis . An inaccurate mass air flow (MAF) sensor-Refer to Scan Tool Data List . Blockage on the inlet screen of the MAF sensor Vacuum hoses that are split, kinked, or improperly connected An air intake duct that is collapsed or restricted-Refer Intake Air Resonator Replacement . An air filter that is dirty or restricted-Refer to Air Cleaner Element Replacement . Inspect for the following conditions that may cause the engine to run lean: NOTE: Refer to Heated Oxygen and Oxygen Sensor Notice in Cautions and Notices. Water intrusion in the HO2S connector An exhaust leak between the HO2S and the engine-Refer to Exhaust Leakage in Engine Exhaust. Vacuum leaks Incorrect fuel pressure-Refer to Fuel System Diagnosis . Restricted fuel injectors-Refer to Fuel System Diagnosis . An inaccurate MAF sensor-Refer to Scan Tool Data List . Fuel contamination-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (With Special Tool) . Vacuum hoses that are split, kinked, or improperly connected
Sensor/System	Use a scan tool in order to monitor the knock sensor (KS) system for excessive spark retard activity.
Ignition System	Soak the secondary ignition system with water from a spray bottle. Soaking the secondary ignition system may help locate damaged or deteriorated components. Look and listen for arcing or misfiring as you apply water. Test for proper ignition voltage output with the J 26792 Spark Tester. Remove the spark plugs and inspect for the following conditions: Correct heat range Wet plugs Cracks Wear Improper gap Burned electrodes Heavy deposits Refer to Spark Plug Inspection . An improper spark plug gap may cause a driveability problem. Refer to Spark Plug Inspection . Gap the spark plugs using a wire gauge gap tool. Refer to Spark Plug Replacement . Determine the cause of the fouling before replacing the spark plugs. Visually and physically inspect the secondary ignition for the following conditions: The ignition wires arcing to ground The ignition wires for proper engagement to spark plug The ignition coils for cracks or carbon tracking Monitor the Misfire Current Counters while driving the vehicle in the conditions that the misfire occurred. If a misfiring cylinder can be located, use the DTC P0300 table for diagnosis. Refer to DTC P0300 .
Engine Mechanical	Inspect engine mechanical for the following conditions: Inspect compression-Refer to Engine Compression Test in Engine Mechanical. Sticking or leaking valves Worn camshaft lobes Valve timing Bent push rods Worn rocker arms Broken valve springs Excessive oil in combustion chamber-Refer to Oil Consumption Diagnosis in Engine Mechanical. For incorrect basic engine parts inspect the following: The camshaft-Refer to Camshaft and Bearings Cleaning and Inspection in Engine Mechanical. The cylinder heads-Refer to Cylinder Head Cleaning and Inspection in Engine Mechanical. The pistons, etc.-Refer to Piston, Connecting Rod, and Bearings Cleaning and Inspection in Engine Mechanical. Refer to Symptoms - Engine Mechanical in Engine Mechanical for diagnostic procedures.
Additional Inspections	Inspect the exhaust system for possible restrictions. Inspect for the following: Inspect the exhaust system for damaged or collapsed pipes. Inspect the mufflers for heat distress or possible internal failure. Inspect for possible plugged catalytic converters by comparing the exhaust system back pressure on each side of engine. Refer to Restricted Exhaust in Engine Exhaust. Electromagnetic interference (EMI) on the reference circuit can cause an engine misfire condition. A sudden increase in indicated RPM with little change in actual engine RPM change indicates EMI is present. Inspect for high voltage components near ignition control circuits if a condition exists. Inspect the intake manifold and the exhaust manifold passages for casting flash.