LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2006 >> Escalade AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 785 (Engine Control System - 8.1L - DTC P0506 To DTC U0107) >> DTC P1133 or P1153 >> Test Description

Test Description

WARNING: This page is about a different car, the 2006 GMC Yukon XL, 2006 Chevrolet Suburban, and 2006 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.

The number below refers to the step number on the diagnostic table.

  1. 2:  If the voltage is varying above and below the specified value, the condition is not present.
DTC P1133 or P1153

Step Action Value(s) Yes No
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Powertrain Control Module (PCM) Connector End Views or Engine Controls Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Start the engine.
  2. Allow the engine to reach operating temperature. Refer to Scan Tool Data List .
  3. Operate the engine at 1,500 RPM for 30 seconds.
  4. Observe the affected heated oxygen sensor (HO2S) voltage parameter with a scan tool.
Is the HO2S voltage parameter varying above and below the specified range?		 250-625 mV Go to Step 3  Go to Step 4 
3
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 4  Go to Testing for Intermittent Conditions and Poor Connections
4
  1. Turn OFF the ignition.
  2. Disconnect the affected HO2S.
  3. Turn ON the ignition, with the engine OFF.
  4. Observe the HO2S voltage parameter with a scan tool.
Is the HO2S voltage parameter less than the specified value?		 100 mV Go to Step 6  Go to Step 5 
5
  1. Connect a 3-amp fused jumper wire between the high signal circuit of the HO2S harness connector on the engine harness side and a good ground.
  2. Observe the HO2S voltage parameter with a scan tool.
Is the HO2S voltage parameter less than the specified value?		 100 mV Go to Step 8  Go to Step 7 
6 Test the HO2S high signal circuit for a short to the HO2S low signal circuit. Refer to the following procedures:
Did you find and correct the condition?		 - Go to Step 14  Go to Step 11 
7 Test the HO2S high signal circuit for an open or high resistance. Refer to the following procedures:
Did you find and correct the condition?		 - Go to Step 14  Go to Step 11 
8
  1. Remove the jumper wire from the previous step.
  2. Connect a 3-amp fused jumper wire between the high signal circuit of the HO2S harness connector on the engine harness side and the low signal circuit of the HO2S harness connector on the engine harness side.
  3. Observe the HO2S voltage parameter with a scan tool.
Is the HO2S voltage parameter less than the specified value?		 100 mV Go to Step 10  Go to Step 9 
9 Test the HO2S low signal circuit for an open, or high resistance. Refer to the following procedures:
Did you find and correct the condition?		 - Go to Step 14  Go to Step 11 
10 Test for shorted terminals and for poor connections at the HO2S. Refer to the following procedures:
Did you find and correct the condition?		 - Go to Step 14  Go to Step 12 
11 Test for shorted terminals and for poor connections at the powertrain control module (PCM). Refer to the following procedures:
Did you find and correct the condition?		 - Go to Step 14  Go to Step 13 
12
NOTE: Refer to Silicon Contamination of Heated Oxygen Sensors Notice .
IMPORTANT: The HO2S may be damaged due to contamination. Prior to replacing the HO2S inspect for the following sources of contamination:
Replace the affected HO2S. Refer to Heated Oxygen Sensor (HO2S) Replacement Bank 1 Sensor 1 or Heated Oxygen Sensor (HO2S) Replacement Bank 2 Sensor 1 .Did you complete the replacement?		 - Go to Step 14  -
13 Replace the PCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 14  -
14
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 15 
15 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals