LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2005 >> Escalade ESV >> Repair and Diagnosis >> External Pages >> Different car >> Section 150 (Automatic Transmission - 4L80-E/4L85-E - Overhaul) >> Repair Instructions >> Turbine Shaft Assemble

Turbine Shaft Assemble

WARNING: This page does not describe the selected car, but rather 13 other vehicles, including the 2005 GMC Yukon XL, 2005 GMC Sierra, 2005 GMC Savana Special, 2005 GMC Savana Camper Special, and 2005 GMC Savana. However, it is still accessible from the selected car via links, so may be relevant.

Tools Required

    Fig 1: Installing Turbine Shaft Intermediate Oil Seal Ring Using J 38736-1 & J 38736-5
    GM31141Courtesy of GENERAL MOTORS CORP.
  1. Place the J 38736-1  onto the turbine shaft (502). See Special Tools .
  2. Set the J 38736-1  to position #1. See Special Tools .
  3. Using the J 38736-5  , install the lower turbine shaft intermediate oil seal ring (501). See Special Tools .
  4. Remove the tools.
    5. Fig 2: Sizing Lower Turbine Shaft Intermediate Oil Seal Ring Using J 38736-3
    GM31181Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Be sure to use the small chamfered end of the J 38736-3  in order to size the lower turbine shaft intermediate oil seal ring. See Special Tools . Then use the larger chamfered end of the J 38736-3  in order to size the upper turbine shaft intermediate oil seal ring.
  5. With the small chamfered end down, place the J 38736-3  over the lower turbine shaft intermediate oil seal ring. See Special Tools .
  6. Leave the J 38736-3  on the turbine shaft intermediate oil seal ring for at least 1 minute in order to allow the seal ring to become the proper size. See Special Tools .
    7. Fig 3: Installing Turbine Shaft Intermediate Oil Seal Ring Using J 38736-1 & J 38736-5
    GM31141Courtesy of GENERAL MOTORS CORP.
  7. Place the J 38736-1  onto the turbine shaft (502). See Special Tools .
  8. Set the J 38736-1  to position #2. See Special Tools .
  9. Using the J 38736-5  , install the upper turbine shaft intermediate oil seal ring (501). See Special Tools .
  10. Remove the tools.
    11. Fig 4: Placing J 38736-3 Over Turbine Shaft Intermediate Oil Seal Ring
    GM40708Courtesy of GENERAL MOTORS CORP.
  11. With the large chamfered end down, place the J 38736-3  over the turbine shaft intermediate oil seal ring. See Special Tools .
  12. Leave the J 38736-3  on the turbine shaft intermediate oil seal ring for at least 1 minute to allow the seal ring to become the proper size. See Special Tools .
    13. Fig 5: Installing Turbine Shaft Rear Oil Seal Ring Using J 38736-2 & J 38736-6
    GM31183Courtesy of GENERAL MOTORS CORP.
  13. Turn the turbine shaft (502) over.
  14. Place the J 38736-2  onto the turbine shaft. See Special Tools .
  15. Set the J 38736-2  to position #1. See Special Tools .
  16. Using the J 38736-6  , install the lower turbine shaft rear oil seal ring (503). See Special Tools .
  17. Remove the tools.
    18. Fig 6: Installing Small End Of J 38736-4 Over Turbine Shaft Rear Oil Seal Ring
    GM40709Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Be sure to use the small chamfered end of the J 38736-4  in order to size the lower turbine shaft rear oil seal ring. See Special Tools . Then use the larger chamfered end of the J 38736-4  in order to size the upper turbine shaft rear oil seal ring.
  18. With the small chamfered end down, place the J 38736-4  over the lower turbine shaft rear oil seal ring. See Special Tools .
  19. Leave the J 38736-4  on the turbine shaft rear oil seal ring for at least 1 minute in order to allow the seal ring to become the proper size. See Special Tools .
    20. Fig 7: Installing Turbine Shaft Rear Oil Seal Ring Using J 38736-2 & J 38736-6
    GM31183Courtesy of GENERAL MOTORS CORP.
  20. Place the J 38736-2  onto the turbine shaft (502). See Special Tools .
  21. Set the J 38736-2  to position #2. See Special Tools .
  22. Using the J 38736-6  , install the upper turbine shaft rear oil seal ring (503). See Special Tools .
  23. Remove the tools.
    24. Fig 8: Installing Large End Of J 38736-4 Over Turbine Shaft Rear Oil Seal Ring
    GM31184Courtesy of GENERAL MOTORS CORP.
  24. With the large chamfered end down, place the J 38736-4  over the turbine shaft rear oil seal ring. See Special Tools .
  25. Leave the J 38736-4  on the turbine shaft rear oil seal ring for at least 1 minute in order to allow the seal ring to become the proper size. See Special Tools .
scientia non olet · About LEMON Manuals