LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2004 >> Seville >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel System Displays, Gauges And Console >> Repair Instructions >> Instrument Panel (I/P) Retainer Replacement >> Installation Procedure

Installation Procedure

    Fig 1: Identifying I/P Retainer Bolts
    GM751440Courtesy of GENERAL MOTORS CORP.
  1. Install the Ignition switch to the I/P retainer. Refer to Ignition Switch Replacement (LHD)  or Ignition Switch Replacement (RHD) .
  2. Install the Inside air temperature sensor to the I/P retainer. Refer to Inside Air Temperature Sensor Assembly Replacement (LHD) in HVAC Systems-Automatic.
  3. Partially install the I/P retainer (1) to the carrier (2).

    Guide the wiring through the I/P retainer openings.

  4. Connect the inside air temperature sensor electrical connector.
  5. Connect the ignition switch electrical connectors.
    6. NOTE: Refer to Fastener Notice in Cautions and Notices.
  6. Install the I/P retainer (1) bolts.

    Tighten:  Tighten the bolts to 2 N.m (18 lb in).

    7. Fig 2: Identifying Park Lock Cable
    GM339237Courtesy of GENERAL MOTORS CORP.
  7. Turn the ignition to the run position.
  8. Align the park lock cable tab (1) with the ignition switch.
  9. Push the cable towards the ignition switch until an audible click is heard indicating the release button is engaged.
    10. Fig 3: Identifying Steering Column Nuts
    GM754218Courtesy of GENERAL MOTORS CORP.
  10. Install the steering column. Refer to Steering Column Replacement in Steering Wheel and Column.
    11. Fig 4: Identifying I/P Retainer Bolt
    GM530762Courtesy of GENERAL MOTORS CORP.
  11. Install the I/P retainer bolt (1) located in the opening for the fuel/rear compartment switch assembly.

    Tighten:  Tighten the bolt to 2 N.m (18 lb in).

    12. Fig 5: Identifying HVAC Duct/ I/P Retainer Bolt
    GM751047Courtesy of GENERAL MOTORS CORP.
  12. Install the HVAC duct I/P retainer bolt (1), located below the HVAC duct, on the drivers side.

    Tighten:  Tighten the bolt to 2 N.m (18 lb in).

    13. Fig 6: Identifying I/P Screws
    GM751046Courtesy of GENERAL MOTORS CORP.
  13. Install the I/P screw (1) at each end of the I/P retainer.

    Tighten:  Tighten the bolts to 2 N.m (18 lb in).

  14. Install the fuel/rear compartment release switch. Refer to Rear Compartment Lid Switch Replacement in Body Rear End.
  15. Install the headlamp switch. Refer to Headlamp Switch Replacement (LHD) in Lighting Systems.
  16. Install the knee bolster. Refer to Knee Bolster Replacement .
  17. Install the radio. Refer to Radio Replacement (U45) or Radio Replacement (U1R, UL6, UM5, UM9) in Entertainment.
  18. Install the I/P cluster. Refer to Instrument Panel Cluster (IPC) Replacement .
  19. Install the I/P storage compartment. Refer to Compartment Replacement - Instrument Panel (I/P) .
  20. Install the left I/P accessory trim plate. Refer to Trim Plate Replacement - Instrument Panel (I/P) Accessory Left (LHD)  or Trim Plate Replacement - Instrument Panel (I/P) Accessory Left (RHD) .
  21. Install the right I/P accessory trim plate. Refer to Trim Plate Replacement - Instrument Panel (I/P) Accessory Right (LHD)  or Trim Plate Replacement - Instrument Panel (I/P) Accessory Right (RHD) .
  22. Install the I/P outer trim cover. Refer to Instrument Panel (I/P) Outer Trim Cover Replacement 
  23. Install the center console. Refer to Console Replacement (w/o UV8)  or Console Replacement (w/ UV8) .
  24. Connect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical.
  25. Enable the SIR. Refer to SIR Disabling and Enabling Zone 3 and SIR Disabling and Enabling Zone 5 in SIR.
scientia non olet · About LEMON Manuals