Chime Inoperative
Chime Inoperative
| Step | Action | Values | Yes | No |
|---|---|---|---|---|
| Schematic Reference: Audible Warnings Schematics DEFINITION: One or more chime functions are inoperative. |
||||
| 1 | Did you perform the Audible Warnings Diagnostic System Check? | - | Go to Step 2 | Go to Diagnostic System Check - Audible Warnings |
| 2 |
|
- | Go to Step 3 | Go to Speakers Inoperative - One or More in Entertainment |
| 3 |
|
- | Go to Step 4 | Go to Door Ajar Indicator Malfunction in Doors |
| 4 |
|
- | Go to Step 5 | Go to Headlamps Inoperative - Low Beams (Domestic, Europe and Japan) or Headlamps Inoperative - Low Beams (Domestic, Europe and Japan w/ HID) or Headlamps Inoperative - Low Beams (Norway/Sweden) or Headlamps Inoperative - Low Beams (Norway/Sweden w/ HID) in Lighting Systems |
| 5 |
|
- | Go to Step 7 | Go to Step 6 |
| 6 |
|
- | Go to Step 9 | Go to Step 8 |
| 7 |
|
0.6-0.7 V | Go to Step 14 | Go to Step 10 |
| 8 | Test the key in ignition signal circuit for an open or for a high resistance. Refer to Circuit Testing
and to Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 13 |
| 9 | Test the ground circuit of the key in ignition switch for an open. Refer to Circuit Testing
and to Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 12 |
| 10 | Test the chime module bit 1 signal circuit for a for an open, for a short to ground, or for a short to voltage. Refer to Circuit Testing
and to Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 11 |
| 11 | Test the chime module bit 2 signal circuit for a for an open, for a short to ground, or for a short to voltage. Refer to Circuit Testing
and to Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 15 |
| 12 | Inspect for poor connections at the harness connector of the ignition switch. Refer to Testing for Intermittent Conditions and Poor Connections
and to Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 16 |
| 13 | Inspect for poor connections at the harness connector of the IPM. Refer to Testing for Intermittent Conditions and Poor Connections
and to Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 17 |
| 14 | Inspect for poor connections at the harness connector of the amplifier. Refer to Testing for Intermittent Conditions and Poor Connections
and to Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 18 |
| 15 | Inspect for poor connections at the harness connector of the radio. Refer to Testing for Intermittent Conditions and Poor Connections
and to Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 19 |
| 16 | Replace the ignition switch. Refer to Ignition Switch Replacement (LHD) or Ignition Switch Replacement (RHD) . Did you complete the replacement? |
- | Go to Step 20 | - |
| 17 |
IMPORTANT:
Perform the set up procedure for the replacement IPM. Replace the IPM. Refer to Instrument Panel Module Replacement (LHD)
or Instrument Panel Module Replacement (RHD)
in Body Control System.Did you complete the replacement? |
- | Go to Step 20 | - |
| 18 | Replace the amplifier. Refer to Amplifier Replacement (UX9)
or Amplifier Replacement (w/o UX9)
in Entertainment. Did you complete the replacement? |
- | Go to Step 20 | - |
| 19 | Replace the radio. Refer to Radio Replacement (U45)
or Radio Replacement (U1R, UL6, UM5, UM9)
in Entertainment. Did you complete the replacement? |
- | Go to Step 20 | - |
| 20 | Operate the system in order to verify the repair. Did you correct the condition? |
- | System OK | Go to Step 2 |