LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2004 >> CTS Base, 3.6 7 >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 7 (Engine Mechanical - 3.2L) >> Repair Instructions >> On-Vehicle Repair Instructions >> Engine Support Fixture >> Installation Procedure

Installation Procedure

WARNING: This page is about a different variant/trim than selected.
  1. Loosely install the J 28467-501  (1) to the ends of the strut tower tube J 28467-3  (2).
    Fig 1: Identifying J 28467-B & J 28467-3
    GM790666Courtesy of GENERAL MOTORS CORP.
    2. Fig 2: View Of J 28467-501 & J 28467-3
    GM790668Courtesy of GENERAL MOTORS CORP.
  2. Place the strut tower tube J 28467-3  and the J 28467-501  on top of both the left and right fender lips, over the engine rear lift bracket.
  3. Install the radiator shelf tube J 28467-2A  (2) on top of the strut tower tube J 28467-3  (1) over the engine front lift bracket.
    Fig 3: Identifying J 28467-2A & J 28467-3
    GM790672Courtesy of GENERAL MOTORS CORP.
  4. Install the round tube of the front support assembly J 28467-4A through the large hole in the radiator shelf tube J 28467-2A. The hole used in the radiator shelf tube J 28467-2A depends on the vehicle application.
  5. Place the rubber padded foot of the front support assembly J 28467-4A on the upper tie bar.
  6. Install the 7/16 in x 2.0 in quick release pin J 28467-9 through the hole in the front support assembly J 28467-4A in order to level the radiator shelf tube J 28467-2A.
    Fig 4: Installing Quick Release Pin J 28467-9
    GM405958Courtesy of GENERAL MOTORS CORP.
  7. Install the cross bracket assembly J 28467-1A  .
    Fig 5: Identifying J 28467-1A
    GM287864Courtesy of GENERAL MOTORS CORP.
  8. Hand tighten the cross bracket assembly J 28467-1A  wing nuts.
  9. Install the lift hook J 28467-7A  through the lift hook bracket J 28467-6A  .
    Fig 6: View Of Lift Hook Assembly
    GM682139Courtesy of GENERAL MOTORS CORP.
  10. Install the 1/2 in lift hook washer and lift hook wing nut J 28467-34  onto the lift hook J 28467-7A  .
  11. Install the assembled lift hook bracket J 28467-6A  (1) over the strut tower tube J 28467-3  (2).
    Fig 7: View Of Lift Hook & Bracket Assembly At Longitudinal Mounted Cross Bar
    GM682301Courtesy of GENERAL MOTORS CORP.
  12. Adjust the assembled lift hook bracket J 28467-6A  (1) in order to align the hook with the engine rear lift bracket.
  13. Install the lift hook J 28467-7A  through the engine rear lift bracket. Ensure the hook does not damage the surrounding components.
    Fig 8: View Of Lift Hook Through Engine Rear Lift Bracket
    GM790674Courtesy of GENERAL MOTORS CORP.
  14. Repeat steps 9 and 10.
  15. Install the assembled lift hook bracket J 28467-6A  (1) over the radiator shelf tube J 28467-2A  (2).
    Fig 9: View Of Lift Hook & Bracket Assembly At Longitudinal Mounted Cross Bar
    GM682301Courtesy of GENERAL MOTORS CORP.
  16. Adjust the assembled lift hook bracket J 28467-6A  (1) in order to align the hook with the engine front lift bracket.
  17. Install the lift hook J 28467-7A  through the engine front lift bracket. Ensure the hook does not damage the surrounding components.
    Fig 10: View Of Lift Hook Through Engine Front Lift Bracket
    GM790676Courtesy of GENERAL MOTORS CORP.
  18. Hand tighten the lift hook wing nuts J 28467-34  securely to remove all slack from the engine support fixture assembly.
    Fig 11: View Of Engine Support Fixture Assembly
    GM790677Courtesy of GENERAL MOTORS CORP.
scientia non olet · About LEMON Manuals