LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2004 >> CTS Base, 3.6 7 >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 10 (Engine Controls - 2.6L & 3.2L - Troubleshooting & Diagnosis) >> Troubleshooting >> Fuel System Diagnosis >> Test Description

Test Description

WARNING: This page is about a different variant/trim than selected.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step verifies that the fuel pump is operating.
  2. 4:  This step verifies that the vehicle is not out of fuel. If the right fuel sender is below 0.8 V, and the left fuel sender is above 0.8 V, a fuel transfer condition exists.
  3. 7:  This step tests for an internal fuel leak. If the fuel pressure drops during this test, then an internal loss of pressure is indicated.
  4. 10:  This step isolates the condition. Replace the primary fuel tank module assembly, if the fuel pressure remains constant, after closing the valve on the fuel pipe shut-off adapter. Locate and replace the leaking fuel injector if the pressure continues to decrease after closing the valve on the adapter.
  5. 13:  This step isolates the condition. Replace the primary fuel tank module assembly for a stuck open or leaking fuel pressure regulator, if the fuel pressure increases above the specified value.
  6. 16:  This step verifies that a circuit condition is not the cause of a fuel pressure concern. Inspect all fuel pump electrical circuits thoroughly.
Fuel System Diagnosis

Step Action Value(s) Yes No
Schematic Reference:  Fuel Hose/Pipes Routing Diagram 
1 Did you perform the Diagnostic System Check-Engine Controls? - Go to Step 2  Go to Diagnostic System Check - Engine Controls
2 
IMPORTANT: Inspect the fuel system for the following conditions before proceeding with this diagnostic procedure:
  • Damage to the fuel system
  • External fuel leaks
  1. Turn ON the ignition, with the engine OFF.
  2. Command the fuel pump ON with a scan tool.
Does the fuel pump operate?		 - Go to Step 3  Go to Fuel Pump Electrical Circuit Diagnosis 
3 Observe the fuel level sensor left voltage with a scan tool.
Is the fuel level sensor left voltage less than the specified value?		 0.8 V Go to Step 4  Go to Step 6 
4  Observe the fuel level sensor right voltage with a scan tool.
Is the fuel level sensor right voltage less than the specified value?		 0.8 V Go to Step 5  Go to Step 14 
5
  1. Add the specified amount of fuel.
  2. Operate the vehicle within the conditions of the customer's concern.
  3. Monitor the fuel trim related parameters with a scan tool. Refer to Scan Tool Data List .
Do any of the scan tool parameters indicate a lean condition?		 19 liters (5 gallons) Go to Step 15  Go to Symptoms - Engine Controls 
6
  1. Turn OFF the ignition.
  2. Install the fuel pressure gage. Refer to Fuel Pressure Gage Installation and Removal .
  3. Turn ON the ignition, with the engine OFF.
    4. IMPORTANT:
    • The fuel pump may need to be commanded ON a few times in order to obtain the highest possible fuel pressure.
    • DO NOT start the engine.
  4. Command the fuel pump ON with a scan tool.
  5. Observe the fuel pressure gage, while the fuel pump is operating.
Is the fuel pressure within the specified range?		 380-410 kPa (55-60 psi) Go to Step 7  Go to Step 11 
7 
IMPORTANT: The fuel pressure will drop when the fuel pump stops operating. After the fuel pump stops operating, the fuel pressure should stabilize and remain constant.
  1. Allow the fuel pressure to stabilize.
  2. Observe the fuel pressure gage for 1 minute.
Does the fuel pressure decrease by more than the specified value?		 34 kPa (5 psi) Go to Step 10  Go to Step 8 
8
  1. Relieve the fuel pressure to the first specified value.
  2. Observe the fuel pressure gage for 5 minutes.
Does the fuel pressure decrease by more than the second specified value?		 69 kPa (10 psi)
14 kPa (2 psi)		 Go to Step 19  Go to Step 9 
9
  1. Operate the vehicle within the conditions of the customer's concern.
  2. Observe the fuel related parameters with a scan tool.
Do any of the scan tool parameters indicate a lean condition?		 - Go to Step 15  Go to Symptoms - Engine Controls 
10 
  1. Turn OFF the ignition.
  2. Relieve the fuel pressure. Refer to Fuel Pressure Relief Procedure .
  3. Disconnect the fuel feed pipe from the fuel rail. Refer to Quick Connect Fitting(s) Service (Metal Collar) .
  4. Install the appropriateJ 37287  Fuel Pipe Shut-off Adapter between the fuel feed pipe and the fuel rail inlet.
  5. Open the valve on the fuel feed pipe shut-off adapter.
  6. Command the fuel pump ON, with a scan tool.
  7. Bleed the air from the fuel system.
  8. Command the fuel pump ON, with a scan tool.
  9. Close the fuel pipe shut-off valve.
  10. Observe the fuel pressure gage for 1 minute.
Does the fuel pressure remain constant?		 - Go to Step 19  Go to Step 18 
11 Is the fuel pressure more than the specified value? 410 kPa (60 psi) Go to Step 12  Go to Step 13 
12 Inspect the fuel return hose/pipe at the fuel filter for a restriction.
Did you find and correct the condition?		 - Go to Step 20  Go to Step 19 
13 
  1. Turn OFF the ignition.
  2. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure .
  3. Disconnect the fuel return hose from the fuel return outlet of the fuel filter. Refer to Quick Connect Fitting(s) Service (Metal Collar) .
  4. Install the appropriate J 37287  between the return outlet of the fuel filter and the fuel return hose.
  5. Open the valve in the fuel pipe shut-off adapter.
  6. Turn ON the ignition, with the engine OFF.
  7. Command the fuel pump ON, with a scan tool.
  8. Bleed the air from the fuel system.
  9. Observe the fuel pressure gauge.
  10. Slowly close the valve in the fuel pipe shut-off adapter.
  11. Use a scan tool in order to command the fuel pump ON.
Does the fuel pressure increase to more than the specified value?		 380-410 kPa (55-60 psi) Go to Step 19  Go to Step 15 
14
  1. Remove both fuel tank modules. Refer to Fuel Tank Module Replacement - Primary and Fuel Tank Module Replacement - Secondary .
  2. Inspect the feed fuel pipe of the siphon jet pump for a restriction.
  3. Inspect the fuel strainer for contaminants. Refer to Alcohol/Contaminants-in-Fuel Diagnosis (w/o Special Tool)  or Alcohol/Contaminants-in-Fuel Diagnosis (w/ Special Tool) .
Did you find and correct the condition?		 - Go to Step 20  Go to Step 19 
15 Inspect the following components for a restriction:
  • The fuel filter
  • The fuel feed pipe

Did you find and correct the condition?		 - Go to Step 20  Go to Step 16 
16  Test for an intermittent and for a poor connection at the primary fuel tank module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 20  Go to Step 17 
17
  1. Remove the primary fuel tank module. Refer to Fuel Tank Module Replacement - Primary .
  2. Inspect the following items:
Did you find and correct the condition?		 - Go to Step 20  Go to Step 19 
18
  1. Turn OFF the ignition.
  2. Raise the fuel rail, with the fuel lines connected. Refer to Fuel Injectors and Fuel Rail Replacement .
  3. Turn ON the ignition, with the engine OFF.
  4. Command the fuel pump ON with a scan tool.
  5. Locate and replace the leaking fuel injector. Refer to Fuel Injectors and Fuel Rail Replacement .
Did you complete the replacement?		 - Go to Step 20  -
19 Replace the primary fuel tank module. Refer to Fuel Tank Module Replacement - Primary .
Did you complete the replacement?		 - Go to Step 20  -
20 Operate the system in order to verify the repair.
Did you correct the condition?		 - System OK Go to Step 3 
scientia non olet · About LEMON Manuals