LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2004 >> CTS Base, 3.6 7 >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 10 (Engine Controls - 2.6L & 3.2L - Troubleshooting & Diagnosis) >> Troubleshooting >> Fuel Injector Balance Test with Special Tool >> Test Description

Test Description

WARNING: This page is about a different variant/trim than selected.

The numbers below refer to the step numbers on the diagnostic table.

  1. 3:  The engine coolant temperature (ECT) must be below the operating temperature in order to avoid irregular fuel pressure readings due to hot soak fuel boiling.
  2. 6:  If the pressure drop value for each fuel injector is within 10 kPa (1.5 psi) of the average pressure drop value, the fuel injectors are flowing properly. Calculate the pressure drop value for each fuel injector by subtracting the second pressure reading from the first pressure reading. Refer to the Fuel Injector Balance Test Example.
Fuel Injector Balance Test Procedure

Step Action Values Yes No
1 Did you perform the Diagnostic System Check-Engine Controls? - Go to Step 2  Go to Diagnostic System Check - Engine Controls
2 Did you perform the Fuel Injector Coil Test? - Go to Step 3  Go to Fuel Injector Coil Test 
3 
IMPORTANT: DO NOT perform this test if the engine coolant temperature is above 94°C (201°F).
Observe the ECT with a scan tool.Is the ECT less than the specified value?		 94°C (201°F) Go to Step 4  -
4
IMPORTANT: Verify that adequate fuel is in the fuel tank before proceeding with this diagnostic.
  1. Turn OFF the ignition.
  2. Install the fuel pressure gage. Refer to Fuel Pressure Gage Installation and Removal .
  3. Turn ON the ignition, with the engine OFF.
    4. IMPORTANT:
    • The fuel pump may need to be commanded ON a few times, in order to obtain the highest possible fuel pressure.
    • DO NOT start the engine.
  4. Command the fuel pump ON with a scan tool.
  5. Observe the fuel pressure gage, with the fuel pump commanded ON.
Is the fuel pressure within the specified range?		 337-379 kPa (49-55 psi) Go to Step 5  Go to Fuel System Diagnosis 
5
IMPORTANT: The fuel pressure will drop slightly when the fuel pump stops operating. After the fuel pump stops operating, the fuel pressure should stabilize and remain constant.
Monitor the fuel pressure gage for 1 minute.Does the fuel pressure decrease by more than the specified value?		 34 kPa (5 psi) Go to Fuel System Diagnosis  Go to Step 6 
6 
  1. Connect the J 39021  Fuel Injector Coil/Balance Tester, J 39021-210  Injector Tester Adapter Box, and J 39021-360  Fuel Injector Test Adapter to the fuel injector harness multi-way connector.
  2. Set the amperage supply selector switch on the fuel injector tester to the Balance Test 0.5-2.5 amp position.
  3. Command the fuel pump ON and then OFF with a scan tool.
  4. Record the fuel pressure indicated by the fuel pressure gage after the fuel pressure stabilizes. This is the first pressure reading.
    5. IMPORTANT: Record the fuel pressure value immediately after the fuel injector stops pulsing. The fuel pressure may rise after the fuel injector stops pulsing. DO NOT record the higher fuel pressure value.
  5. Energize the fuel injector by depressing the Push to Start Test button on the fuel injector tester.
  6. Record the fuel pressure indicated by the fuel pressure gage after the fuel injector stops pulsing. This is the second fuel pressure reading.
  7. Repeat steps 1 through 6 for each fuel injector.
  8. Subtract the second pressure reading from the first pressure reading for one fuel injector. The result is the pressure drop value.
  9. Obtain a pressure drop value for each fuel injector.
  10. Add all of the individual pressure drop values. This is the total pressure drop.
  11. Divide the total pressure drop by the number of fuel injectors. This is the average pressure drop.
Does any fuel injector have a pressure drop value that is more than the average pressure drop or less than the average pressure drop by the specified value?		 10 kPa (1.5 psi) Go to Step 7  Go to Symptoms - Engine Controls 
7 Replace the affected fuel injector. Refer to Fuel Injectors and Fuel Rail Replacement .
Did you complete the replacement?		 - Go to Step 8  -
8 Operate the system in order to verify the repair.
Did you correct the condition?		 - System OK Go to Symptoms - Engine Controls 
scientia non olet · About LEMON Manuals